STROKER
Mon February 3, 2003 4:42pm
Rating: 10
|
Assembled Engine 2
480ci, All Aluminum w/Crower Billit internal's. Full Port & Polished Heads. Shelby Investment Cast SST Rockers.
|
|
STROKER
Mon February 3, 2003 5:50pm
Rating: 10
|
Passenger Outside
Passenger side of car after setting on the ground. Stainless Steel Specialties Side Pipes really shine and low stance of IRS gives the car a real Down & Dirty Competion Look. Can't Wait to get it on the road.
|
|
STROKER
Mon February 3, 2003 6:09pm
Rating: 10
|
Chassis Full of Engine
Chassis Full of Aluminum FE. IR Fuel Injection controlled by F.A.S.T ECU mounted under Dash. All Electronics hidden from site.
|
|
65 Blur
Fri April 4, 2003 9:51am
|
Boat Ancor Ready
SBC ready to rip. New 64cc Iron Eagle heads, Victor Jr, Holley 750, MSD 6AL Pro Billet Dist. Blaster Coil, K&N filter & breathers, March Pulleys, Roller 1.6 Rockers, you know all the fun stuff.
|
|
vettestr
Tue July 22, 2003 9:51pm
Rating: 10
|
IRS Vette suspension
Rear suspension, fully adjustable with traction bar. Complete VBP rear assembly.
|
|
JLC800
Wed December 10, 2003 12:23pm
Rating: 10
|
IRS 3.54 power-lock
HD axles and swing arm
|
|
STROKER
Wed December 17, 2003 7:26pm
Rating: 10
|
Ruidoso Rod Run 2003
Run to Ruidoso Rod Run
|
|
cobrajeff
Mon December 29, 2003 8:02am
Rating: 10
|
Webers on a 351C
This is my 351C during the "mock-up" stage. I had two sets of headers fabricated - one for the cast iron heads, and another set for the aluminium heads.
|
|
W. MITTY
Mon February 9, 2004 10:25pm
Rating: 10
|
Thomas Kirkham, Man of Iron
Thomas single handedly loads the 427 into the waiting trailer while I shout words of encouragement from behind the camera
|
|
Fake Snake
Thu April 1, 2004 10:36am
Rating: 9.5
|
8.8 IRS
Under the candy apple red lies...
|
|
nanard289
Tue May 18, 2004 4:38am
Rating: 3.5
|
rear half shaft
Unfortunately, I don't find a nice aluminum half shaft for my rear end but only an heavy iron shaft (from a truck)
|
|
Dave Reed
Tue July 27, 2004 12:36am
Rating: 10
|
The Chassis
Waiting for the body.302, Jag IRS, Carrera Shocks , Wilwood four Piston calipers,
|
|
kitcarbp
Tue August 31, 2004 6:30pm
Rating: 10
|
460 Manual Cast Iron Ford Bell Housing (aka 351M/400M Bronco)
351M/400M bell housing- This was actually the first part purchased for my project, wow, what a long strange trip its been ! This required the use of a short-input shaft TKO 600 kit. I used a needle bearing type crankshaft pilot bearing.
Re-cond bell housing waiting for her mate for life
uses a top-loader bolt pattern and only 6.25 inches deep great for STREET duty Cobras. Total investment was $210 after heli-coil repair
|
|
Yetiman
Wed September 1, 2004 8:55pm
Rating: 10
|
Irene getting a ride (CSX2350)
Road America July 04'
|
|
55312
Tue November 2, 2004 12:37pm
Rating: 10
|
|
