Garage10
Sun April 19, 2009 10:37pm
|
bottom left output side
installed a 5/8 hose barb on rads outlet to water pump from surge tank.
|
|
cay5628
Sat May 2, 2009 10:15am
|
Brake Lines
Front brake lines installed
|
|
kitcarbp
Tue May 26, 2009 1:22pm
Rating: 10
|
Denny's Driveshaft Installed
Here is my new custom Denny's Driveshaft Installed using 1330 series rear flange and joint.
|
|
Nickpz1
Thu May 28, 2009 7:38pm
|
Holley/Weiand 174 Supercharger
Installed a Holley Supercharger, 750 Holley Carb, MSD Digital 6+, MDS Boost Timing Master for safety, on a Ford crate 302 with 9:1 compression, Dyno at 360 HP @ 5,800 rpm (still rising) with 360 ft lbs torque flat from 3,000 rpm up, boost stayed under 7 psi to 5,800 rpm
|
|
Nickpz1
Thu May 28, 2009 7:45pm
|
Holley/Weiand 174 Supercharger
Installed a Holley Supercharger, 750 Holley Carb, MSD Digital 6+, MDS Boost Timing Master for safety, on a Ford crate 302 with 9:1 compression, Dyno at 360 HP @ 5,800 rpm (still rising) with 360 ft lbs torque flat from 3,000 rpm up, boost stayed under 7 psi to 5,800 rpm
|
|
fkemmerer
Sun May 31, 2009 12:00pm
Rating: 10
|
ERA 753 with Goodyear Billboards Installed
|
|
fkemmerer
Mon June 1, 2009 1:49am
Rating: 10
|
ERA 753 with Fendor Protectors installed
This is a picture of our ERA at a local cruise night. We have the fendor protectors installed on the front of the rear fenders in this picture
|
|
ZOERA-SC7XX
Fri June 12, 2009 6:09pm
Rating: 10
|
Recent upgrades
Canton Oil Pan Installed
|
|
ZOERA-SC7XX
Fri June 12, 2009 6:09pm
Rating: 10
|
Recent upgrades
Turkey Pan Finished and Installed
|
|
kitcarbp
Tue June 23, 2009 7:01am
Rating: 10
|
alternator fuse with power distribution
I upgraded my electrical system to handle my twin SPAL fans (18A x 2 = 36 AMPS) by installing a modern Alt fuse power box. I used 4 gauge cable from alt to fuse and fuse to battery. It now serves my twin fans and main harness from this point and will give me an underhood power point.
|
|
Pete Munroe
Wed July 22, 2009 9:58pm
Rating: 6
|
Canton oil thermostat
ERA 289 FIA with Canton oil thermostat. This is the drivers side hose run to the cooler.
Off-set the Canton thermostat cooler line outlets by taking it apart and rotating the segments. The segments can "clocked" in 90 degree increments, so the oil cooler hoses can exit on opposing sides. Made plumbing a lot easier in this installation. Fewer angles in the swivel fittings helps avoid any restriction on oil pressure.
|
|
Pete Munroe
Wed July 22, 2009 10:07pm
Rating: 10
|
ERA 289 FIA Canton oil thermostat
Canton oil thermostat installation, right side hose run up to the oil cooler
|
|
Jcmrant
Tue July 28, 2009 5:52pm
|
|
Jcmrant
Tue July 28, 2009 5:52pm
|
|
KarlCSX2498
Tue August 4, 2009 9:02am
Rating: 6
|
Fuel filler port, installed by Nick at Acton Custom
A very nice install by nick, fully TIG welded on the inside. A perfect job.
|
|
