392cobra
Mon May 17, 2004 4:27pm
Rating: 7
|
Noproblemraceway,La.,03/4
Lower left rear control arm failure.
|
|
historicmustang
Fri May 21, 2004 2:14pm
Rating: 10
|
Cobra at Lowes
It doesn't get any better than this!
|
|
simon clemens
Tue June 22, 2004 7:44am
|
sump cut
sump is no longer the lowest point... the chassis is.
|
|
mylesdw
Wed June 30, 2004 12:43pm
|
Jaguar IFS
IFS is Jaguar XJS with fabricated lower wishbone and steering arm. Coil-over is Spax adjustable
|
|
Hang-on
Mon July 19, 2004 11:36am
|
Low-Pro Air Cleaner
In this side view, you can see the low profile that was required of the air cleaner.
|
|
boxhead
Sat July 24, 2004 2:45am
|
Lower shockie mount
Here is a pic showing the lower rear shockie mounts that I made today.
They havent been cleaned up and painted yet so they look alittle rough
|
|
Anthony
Sat August 7, 2004 11:35am
Rating: 10
|
Algon mechanical fuel injection for ford 427 MR
This is a mechanical fuel injection system made in the 1960's, hilborn style, constant flow - low pressure. It has 1 7/8" throttle bores, close to 48mm. This intake was also made with the throttle bores straight up, as opposed to at a 45 degree angle like this one. Probably a good start for an electrical fuel injection conversion. As there are no venturi's, it should flow better than 48IDA's, about 30% better.
|
|
Anthony
Sat August 7, 2004 11:41am
Rating: 10
|
Algon fuel injection for ford 427 MR
This is a mechanical fuel injection system made in the 1960's, hilborn style, constant flow - low pressure. It has 1 7/8" throttle bores, close to 48mm. This intake was also made with the throttle bores straight up, as opposed to at a 45 degree angle like this one. Probably a good start for an electrical fuel injection conversion. As there are no venturi's, it should flow better than 48IDA's, about 30% better.
|
|
historicmustang
Fri August 13, 2004 4:12pm
Rating: 9.90909
|
Bobbie
Bobbie with Cobra at Lowes
|
|
MysteryTrain
Sun August 15, 2004 10:30pm
Rating: 10
|
super low roof line
GT40 Monterey 2004
|
|
wizard
Mon October 4, 2004 6:07am
Rating: 10
|
|
jdean
Sun October 17, 2004 9:42am
Rating: 10
|
Trunk latch, inside lid view
This is the eye that is grabbed by the lower latch hook. You are looking at the inside of the trunk lid.
|
|
cobrajeff
Sun November 21, 2004 6:47am
Rating: 10
|
Weber Guages
Two on top left hold float to proper height; two lower left are for measuring float level. Top right is tang-bending tool, lower right is to measure fuel inlet needle setting. (center tools perform same functions as the two on left, just slightly different designs).
|
|
Nathan Houghton
Tue November 30, 2004 1:08pm
|
Tubular Strutless Lower Control Arms
RCC Strutless Tubular Lower Control Arms
|
|
Michael C Henry
Mon December 13, 2004 9:19pm
Rating: 10
|
new_carb_part
notice in the square primaries, lower ventury, the little brass tube sticking out at about 7 o'clock.What is it for?
|
|
