BB427
Sun February 15, 2004 3:55pm
Rating: 10
|
DSCN0602
Webers ready to go
|
|
BB427
Sun February 15, 2004 3:57pm
Rating: 10
|
DSCN0597
Pearl coated intake and Webers
|
|
speed220mph
Thu February 19, 2004 8:52am
|
M1B McLaren
Preparing to take victory lap at Waterford Hills Raceway, Michigan. Power is from Jerry Titus' T/A engine with Webers fitted.
|
|
Atomsk
Sat April 3, 2004 3:33pm
Rating: 10
|
Love them Webers
mmmmmm, webers
|
|
hardiman
Tue May 4, 2004 7:39pm
Rating: 10
|
weber_sb
Polished Weber Intake For Sale for a 289 or 302
|
|
Brent Mills
Sat May 15, 2004 8:58pm
Rating: 10
|
|
Brent Mills
Sat May 15, 2004 9:00pm
Rating: 10
|
|
FunariB
Mon June 7, 2004 12:47pm
Rating: 10
|
1966_Cobra_09
ERA Replica with 427 Cammer motor and Weber throttle bodies.
|
|
BB427
Wed June 16, 2004 4:41am
Rating: 10
|
DSCN0738
Webers / I Love Them!
|
|
mylesdw
Wed June 30, 2004 12:32pm
Rating: 10
|
Chevy with DCNFs
A rare setup, these Weber DCNFs are from an Aston Martin and the manifold is an Inglese.
|
|
priobe
Wed June 30, 2004 6:26pm
Rating: 10
|
Top View IDA 48
Top View Weber IDA 48
|
|
Full Throttle Al
Sat July 17, 2004 7:02am
Rating: 10
|
CSX4083
The One and Only "Cammer Cobra". Fitted with a NOS 427SOHC with 4 Weber setup.
|
|
hardiman
Mon August 2, 2004 11:28am
Rating: 10
|
48 IDA Webers/Polished intake
|
|
Anthony
Sat August 7, 2004 11:51am
Rating: 10
|
1960's Tecalemit-Jackson fuel injection system for road racing
This fuel injection system was developed in England in the 1960's, primarily aimed at road racing, as opposed to Hilborn/Algon which was more for drag racing. Tecalemit-Jackson apparently had a better partial throttle metering system for road racing, but because it was a continuous flow/low pressure, it didn't develop the max power as good as the Lucas - high pressure sequential fuel injection system that had better fuel atomization, more power. None the less, it still was used, and I heard it was at least tested in GT40's. Holman-Moody was the US distributor. The throttle bodies were based off of the weber 48 IDA, and could be bolted on any weber 48IDA intake, each throttle body separately.
|
|
Anthony
Sat August 7, 2004 12:03pm
Rating: 10
|
Hilborn FE 427 High Riser head Fuel injection
This a 1960's Hilborn Fuel injection system for a ford 427 with High Riser heads. The system consisted of two pieces, two banks of 4 throttle bores, of 2 7/16" diameter, that are bolted to the top of the intake. I believe the intake has the 58mm weber bolt pattern and spacing. As you can see, the throttle bores are straight up, not canted at all. A somewhat rare intake. It has been polished, and no identification marks are visable. This should make alot of top end power.
|
|
