dlampe
Mon February 13, 2006 6:41pm
|
|
Dirtrich
Mon February 13, 2006 8:56pm
Rating: 10
|
SPF 1660 "roadster"
Note the AC badge and wire headlight covers.
|
|
Dirtrich
Tue February 21, 2006 7:43pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker 505hp build sheet...
• Blue printed machined 351W version Early Casting Block ('69) with Block Girdle Installed
• Scat Forged Steel 4.100 Stroke Crankshaft
• H Beam Rods 6.200" - ARP HD Rod Bolts
• Power Forged 10.5 to 1 Flat Top HP Pistons
• J & E Chrome Moly Ring Set
• Heavy Duty Double Roller Dynagear Timing Set
• Comp Cams Hydraulic Roller Retrofit Camshaft
• Clevite H series Racing Bearings
• Polished Edelbrock Victor Jr. cylinder heads
• Chrome Moly Hardened pushrods
• High Intensity Scorpion True Roller Rockers
• Melling HV Oil pump with Hardened FMS Drive Rod.
• Complete Fel-pro Gasket set
• Heavy Duty Harmonic Balancer
• New SFI Approved 10.5 inch Standard Flywheel
• Aluminum Timing cover
• Aluminum Finned Ford Racing Valve Covers
• New Fuel Lines and Gas Filter
• Polished Edelbrock Vic Jr. Single Plane
• Edelbrock 800 cfm 4 barrel w/ electric choke
• Elec Accel Billet Distributor & high voltage Coil
• High Flow Polished Aluminum Water & Fuel Pump
• Champion Spark plugs w/ 8mm ACCEL Spiral Wires
• New Chrome Thermostat Housing
• Oval aluminum finned air cleaner w/ Cobra logo
• Chrome 100 amp. Alternator and Polished Brackets
• March Pulley Setup with Serpentine-Belt
|
|
Dirtrich
Tue February 21, 2006 8:00pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker - dynoed @ 505hp
I like shiny...so I went with full engine polish as well as Jet Hot ceramic coating of the headers, valve covers, manifold, air filter lid and even the scattershield (which is a no no for you racers).
Why stop there...right? So I also used Stainless steel bolt kit and braided fuel lines.
Note the nickel plated AN fittings and billet fuel filter
|
|
Burgs
Wed March 29, 2006 7:40pm
|
|
Burgs
Wed March 29, 2006 7:40pm
Rating: 10
|
|
Burgs
Wed March 29, 2006 7:41pm
|
|
Jim Kellogg
Thu April 27, 2006 5:56pm
Rating: 10
|
351W/385HP in SPF 887
Ford Motorsports 351 crate motor, super tall valve covers, billet caps, remote breather
|
|
Tongue Pirate
Thu May 11, 2006 8:23pm
Rating: 10
|
|
Tongue Pirate
Thu May 11, 2006 8:24pm
Rating: 10
|
|
autoxmike
Mon June 5, 2006 1:50pm
Rating: 9
|
Breather_1
Valve Cover Breather Setup
|
|
JoeLafives
Wed June 7, 2006 9:06am
Rating: 10
|
|
427SnakeSC
Tue June 27, 2006 1:07pm
Rating: 10
|
|
cobra522
Sat September 2, 2006 2:05pm
Rating: 10
|
xtreme flow,Taylor wires, Custom fabbed billet valve covers
|
|
blueovalfanatic
Tue September 5, 2006 1:06pm
Rating: 10
|
Brake Lines
Close-Up shot of brake line running up left frame rail. To help shield it from exhaust heat, I put a section of fuel line hose around the brake line, then covered it in corrugated tubing to make it look a little better.
|
|
