CoupedUp
Wed July 22, 2009 7:35pm
Rating: 10
|
DSC03708b
Pics from the 2009 LA Art Center College of Design Car Classic
|
|
CoupedUp
Wed July 22, 2009 7:35pm
Rating: 10
|
Blastolene Bros. Tank Cra
Pics from the 2009 LA Art Center College of Design Car Classic
|
|
Pete Munroe
Wed July 22, 2009 9:58pm
Rating: 10
|
ERA 289 FIA shoulder harness mount
Roll bar mount for raising the shoulder harness. Moved one of the belt anchors to the outside of the roll bar. For the inside anchor I welded a bracket on the bar. Point was to be symmetrical to where I mounted the seat. Did not mount the seat as suggested in the "offset" position. Wanted it directly back from the pedals. Did lose some leg room by not doing the normal "offset".
|
|
Pete Munroe
Wed July 22, 2009 10:12pm
|
ERA FIA Canton oil thermostat, top view
oil thermostat from the top showing some of the hose runs
|
|
Wbulk
Thu July 30, 2009 12:56pm
Rating: 10
|
Kirkham Alternator Bracket on a B and B
Reasonably priced bracket that allows the alternator to be mounted between the frame and out of the way of the upper hose. I think I paid $50 from Kirkham Motorsports.
|
|
KarlCSX2498
Tue August 4, 2009 1:59pm
Rating: 10
|
New aluminum hood from panel craft, english wheel perfection
|
|
Rob. Smith
Fri August 21, 2009 7:16am
Rating: 10
|
Handbrake_handle_1
I rebuilt the tunnel lower than the original but I raised the handbrake up and away from the seat.
|
|
scales
Sun September 6, 2009 3:42pm
|
Alternative to a prop-rod or chains.
Used a large Turnbuckle from Lowes to keep the hood up.
|
|
cobbindale
Sun September 13, 2009 3:28am
Rating: 10
|
Paint protection
Clear protective paint film applied.
Barel visible line from mid headlight to mid leading edge of gaurd.
|
|
cobbindale
Sun September 13, 2009 3:28am
Rating: 10
|
Paint protection
Clear protective paint film applied to complete from section of car
|
|
TWOOD
Sun September 13, 2009 2:00pm
Rating: 10
|
original and replacement weatherstrip
original from CRII on the right
Replacement from J. C. Whitney on left.
Part number CM132561
bulb is ¾ dia.
|
|
kitcarbp
Mon September 21, 2009 7:20am
Rating: 10
|
West Coast Griffin Rad Brackets
Here is a shot of my custom rad brackets made from 1/8 x 1.5" aluminum strip. Its a two peice design without welds and is adjustable to the core thickness. This core is 2.75" wide. I used High density EPDM sponge foam to line the inside of the bracket to absord vibration and protect the core frame.
|
|
Full Throttle Al
Thu October 1, 2009 11:48am
Rating: 10
|
Cammer_Cobra_017_800x600_
|
|
martrogers
Fri October 2, 2009 11:59pm
|
ac4
Logo in position, just need to remove tape and fix from the underside (which means taking out radiator, draining down etc)
|
|
martrogers
Fri October 2, 2009 11:59pm
|
auto
Mould template particularly important for the Automatic logo. I made a pin template and curved the logo against a mould taken from the body - see bonnet pic.
|
|
