 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
1 |
2 |
3 |
4 |
5 |
6 |
| 7 |
8 |
9 |
10 |
11 |
12 |
13 |
| 14 |
15 |
16 |
17 |
18 |
19 |
20 |
| 21 |
22 |
23 |
24 |
25 |
26 |
27 |
| 28 |
29 |
30 |
|
|
|
|
|
|
CC Advertisers
|
|
|
25 result(s) to your search. (LIVE)
|
Prev Page ·
|
|
luc
Sat February 2, 2002 10:52pm
Rating: 10
|
Shell Valley 351W
First day out in 2002! after a few months of rain - (yes! I live in Belgium)
|
|
Naja
Sat August 17, 2002 11:18am
|
Chassis Rear
Rear view of the West Coast chassis. 9 inch, live axle with 2.73 gearing. 11 inch ventilated brakes. It's heavy, but extremely rigid and makes for a FINE road car.
|
|
Naja
Sat August 17, 2002 11:44am
|
Naked 533 cid EFI
A look at Naja's powerplant with most of the 'accessories' off of it. Atop is a 1200 cfm Accel throttle body, then a Torker II manifold (a significant restriction for this engine), to the new Edelbrock 6066 aluminum heads, 65 lb. Siemens injectors (supplied by an Aeroequip pump). Custom grind roller CompCam with .662 i/e lift, solid lifters, roller rockers under the custom valve cover by Innovation West (only ones like them in the world). A medium stoker with .080 overbore gives 533 cid. Wiseco pistons have 18cc dish to give 9.8:1 compression ratio. I was surprised when the redline was set at 7k, but the 2 people doing the engine work said it would have no trouble handling it.
It dyno'd at 491 hp (5200 rpm) and 548 ft-lbs (4700 rpm) - remember the Torker II being a huge restriction. It was built with reliability (first) in mind, then for torque. The lowest rpm that they data logged during the dyno was 2600, and it was already doing 525 ft-lbs.
This powers a C6 tranny leading to a 9 inch, live rear end with a 2.73 running gear. Haven't run it on the road much, but have gotten over 15 mpg on two, short trips. Spark control completely MSD including 7AL-2, Pro Power HVC coil, billet distributor with Pro cap. All of this is managed by a SpeedPro ECU. It idles at about 950 rpm.
|
|
cobrajeff
Mon December 30, 2002 3:13pm
Rating: 10
|
GT350 at Nelson's Ledges
I used to live outside Akron, Ohio, and used to run my Shelby at Nelson's Ledges when the Cleveland Corvette Club had open track events.
|
|
cobrajeff
Thu February 27, 2003 5:50am
Rating: 10
|
CS Hall of Fame Annex
This is my "spare bedroom", I usually refer to as the "Carroll Shelby Hall of Fame Annex". Cobra books and videos live here.
|
|
Brent Mills
Fri March 5, 2004 5:50pm
Rating: 10
|
03-03-04BrentsNewCobra_031
My first exit of KMP 286. Had to leave her at My parents house for a while, as we're doing some work on our single car garage. Luckly they live only a mile away. 
|
|
mikee
Sat May 1, 2004 12:29pm
Rating: 10
|
mikee's car
1965 427 S/C Roadster
Owned by : Michael Plesh / Cindy Taylor, Sun Valley, Ca.
Frame & Chassis: Factory Five Racing
Base: Vintage 4” round steel tube ladder style
Perimeter: 3⁄4” cold rolled tubing, racecar type
Suspension: Coil Over shocks front, tube rear axel, rear quad shocks
Brakes: Ford 4-wheel disk brakes w/Carbotech pads and stainless steel
braided lines
Steering: Rack and pinion
Drive train: Ford Motor Company
Engine: 1973 Windsor 351 bored .030 over, Edelbrock Performer heads &
manifold, Holley 750 CFM carburetor, MSD billet distributor and MSD ignition, Competion cam, March pullies, Lokar gas pedal Linkage, Carter electic fuel pump, Centerforce clutch, Lakewood scattershield, Steeda clutch quadrant custom shifter
Transmission: World Class T-5
Rear End: 8.8” Ford 373 live axel (SN96)
Exhaust: Custom ceramic coated headers and side pipes
Wheels & Tires: Fronts: 255-45-17 Yokahama
Rear: 275-45-17 Yokahama
Rims: PS Engineering 17” “Halibrand” Type
Body & Paint: Body by Factory Five Racing, Wareham, MA
Paint: Silkens urethane with urethane clear coat
Trim: LeMans gas cap, front and rear chrome over-riders, chrome
rear bumper, sun visors/wind wings
Roll bar: Heavy duty, ceramic coated
Interior: Autometer “Phantom” gauges, carbon fiber dash, Ricarro seats,
custom electronic self-canceling turn signals
Steering Wheel: 13” Momo racing wheel with quick release hub
Windshield: English made, brass with chrome plate
Specifications: 2235 lbs, 325 RWHP, length body 160”, Wheelbase 90”,
4.5” ground clearance
Photography by: Jeff Atherton
|
|
Steve R
Mon August 2, 2004 9:51am
|
|
mickmate
Tue April 5, 2005 7:23pm
Rating: 10
|
CSX3162
Allen Weiss' car. Lives local to me and pops into the cruise nights with it like it's just another hot rod! Very cool.
|
|
letitbe
Mon April 25, 2005 5:24pm
Rating: 10
|
|
|
All times are GMT -7. The time now is 01:16 PM.
Links monetized by VigLink |
