Aussie Mike
Tue February 3, 2004 5:33am
|
Knock Off
Here's one of the pin drive adaprtors I got from Superformance. It came with only the Ford bolt circle on it so I dlled it to fit the Jag bolt circle as well. I machined up some billet center caps and added some self adhesive AC logos I got from finish line. Hopefully I'll have the wheels soon.
|
|
Aussie Mike
Tue February 3, 2004 5:44am
|
Moto Lita Steering wheel
I got the wheel from Finish Line as I've always liked the Moto Lita wheels. I also like the look of the larger 9 bolt boss. Unfortunately there are no 9 bolt bosses available for my suzuki steering column so I machined up my own. I turned down a SAAS 6 bolt boss and machined an adaptor to fit it. This also let me machine up a working horn button for the center of it. The self adhesive AC logo is recesed into the aluminium horn button.
|
|
Aussie Mike
Tue June 1, 2004 11:50pm
|
New diff fill plug
I machined the dif rear cover to fit a fill plug then I bored and slieved the rear cross member to give me access to it. the original Ford diff had the fill plug in the housing but this new diff doesn't have one.
|
|
simon clemens
Fri March 18, 2005 4:14am
|
New Crank Pully
I had a crank pully custom made out of aluminium, the original pully had too many un-needed bits. I also wanted the power steering pump rpm reduced, so I had a smaller pully machined, this should also reduce some load on the engine 
|
|
phatry5
Sun April 17, 2005 10:13pm
|
Dash
All digital, with custom machined rings around each
|
|
Dirtrich
Tue February 21, 2006 7:43pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker 505hp build sheet...
• Blue printed machined 351W version Early Casting Block ('69) with Block Girdle Installed
• Scat Forged Steel 4.100 Stroke Crankshaft
• H Beam Rods 6.200" - ARP HD Rod Bolts
• Power Forged 10.5 to 1 Flat Top HP Pistons
• J & E Chrome Moly Ring Set
• Heavy Duty Double Roller Dynagear Timing Set
• Comp Cams Hydraulic Roller Retrofit Camshaft
• Clevite H series Racing Bearings
• Polished Edelbrock Victor Jr. cylinder heads
• Chrome Moly Hardened pushrods
• High Intensity Scorpion True Roller Rockers
• Melling HV Oil pump with Hardened FMS Drive Rod.
• Complete Fel-pro Gasket set
• Heavy Duty Harmonic Balancer
• New SFI Approved 10.5 inch Standard Flywheel
• Aluminum Timing cover
• Aluminum Finned Ford Racing Valve Covers
• New Fuel Lines and Gas Filter
• Polished Edelbrock Vic Jr. Single Plane
• Edelbrock 800 cfm 4 barrel w/ electric choke
• Elec Accel Billet Distributor & high voltage Coil
• High Flow Polished Aluminum Water & Fuel Pump
• Champion Spark plugs w/ 8mm ACCEL Spiral Wires
• New Chrome Thermostat Housing
• Oval aluminum finned air cleaner w/ Cobra logo
• Chrome 100 amp. Alternator and Polished Brackets
• March Pulley Setup with Serpentine-Belt
|
|
JCoop
Wed May 3, 2006 4:29pm
|
|
1985 CCX
Sat February 3, 2007 2:45pm
Rating: 10
|
New High Flow Milodon
High flow Milodon to partner with the new Fluidyne. Machined and tapped heater ports so they can be nicely plugged. The plugs are Chromed Brass and all new mounting bolts are Stainless.
|
|
1985 CCX
Wed March 21, 2007 5:59pm
|
Vintage Wheel with Adapter
Aluminum wheel with machined hubcentric adapter for Jaguar spindle, forged and polished spinners, center cap, and includes anti-theft option which stops spinner from coming off if wire is not used. Now, I will set out to tone down the shine a bit and change center appearance to gold as per magnesium Halibrand casting.
|
|
1985 CCX
Wed March 21, 2007 5:59pm
|
Vintage Wheel and Adapter
This wheel includes polished forged spinners, machined hubcentric adapters specific to hub, anti-theft safety option, and center cap. Very high quality parts with a great finish. Should be considered during any build or muscle car upgrades.
|
|
1985 CCX
Wed March 21, 2007 6:34pm
Rating: 10
|
Starting to install hubcentric adapters from Vintage Wheel on the CCX
My how the dust settles over and under the car during the winter. Pulled the cover back to start installation of Vintage Wheel pin drive adapters. These parts have been machined prior to shipping to fit perfectly on the Jaguar spindle. Spinners are forged / polished and include Vintage Wheels Safety:Anti-Theft option. This option will not allow spinner to come off without removal of the safety pins.
|
|
1985 CCX
Sat March 24, 2007 2:21pm
Rating: 10
|
Vintage Wheel installed
Installation of Vintage Wheel pin-drive with adapters. Perfect machined fit over the hub for improved ride and safety.
|
|
RRD
Fri April 20, 2007 6:15pm
|
Griffith 400
engine plate machined for pump in/out
|
|
KarlCSX2498
Thu July 19, 2007 4:30pm
Rating: 10
|
HPIM0715
CNC machined 6061 aluminum caliper bracket for CSX4000 Cobra. This bracket will mount a Wilwood Dynalite caliper on the original Cobra upright. this set up is 11.75 x .81 rotor size
|
|
cobrajam
Sun November 18, 2007 6:06pm
|
391 FT Steel Crank
knife edged and lightened, went from 75lbs to 65lbs, 3.78in stroke, .010/.010, machined snout and flywheel face to fit FE
|
|
