Pete C
Sun February 17, 2002 5:07pm
Rating: 10
|
Daily driver.
The Cobra was so much fun, I figured that I needed this to get me through the week!
|
|
ronzara
Sat May 25, 2002 1:22pm
|
Trunk Box Installation
With Body had NO truck box. It was ordered from EM this way for use of large fuel cell,... I needed to box. So....
|
|
cobrajeff
Tue December 2, 2003 5:24am
Rating: 10
|
Collapsible Spare Tire
Here is my "standard" load - Collapsible Spare seated between Halon and Battery box (air inlator bottle in green "wine cooler" bag).
Two folding chairs, California Duster, and emergency tool kit on lower level. Small scissors jack, knock-off hammer, safety wire & pliers, couple screwdrivers and spark plug socket w/rachet.
Soft top is only loaded when it looks like it will be needed. Miscellaneous "waxer" supplies in small black box to right of tool box.
|
|
Secret Squirrel
Tue December 7, 2004 8:18am
Rating: 10
|
Modified Side Pipe Mount Attached
Final installation of side pipe with modified mounting bracket with rubber insulator bolted between with grade 8 bolt and crown lock nut, 12/6/2004. Update: Use 2 Rubber Insulators if needed for leveling.
|
|
Michael C Henry
Tue December 14, 2004 12:36pm
Rating: 10
|
Vintage Air heater
Vintage Air heater defroster compact model. Problem is vacum controls I used cale controled coolant valve needed vacume to operate heater door to make defroster work.could hav eused elbowsto make change in direction upwards to the defroster ducts
|
|
Michael C Henry
Wed December 15, 2004 9:49pm
Rating: 10
|
screw holding whistle
I used a screw to hold the primary float baffel (whistle) no hammers needed
|
|
boxhead
Sun January 2, 2005 1:43am
|
DSC00009
Engine harness with loose ends to tidy up and re route as needed
|
|
simon clemens
Wed April 27, 2005 7:24am
|
Brake relocation
Rear brake relocation was needed to allow clearance between the coilovers and the calipers. Re-drilled calliper mount bracket holes so the caliper sits about 40 degrees foward from original position. Also had to swap Left & Right brake assemblys to opposite sides, so the hand brake cable now will run on top of the axle & still be accuated by a foward movement. I wonder if others have thought of this solution?
|
|
RobV
Mon June 13, 2005 7:20pm
|
Organizing the wiring for the gauges
I found it easiest to wire the dash and tape the wires in place on the dash to organize the loom in the dash area. I planned to add speakers under the dash and needed to make sure there was room.
|
|
RobV
Mon June 13, 2005 7:27pm
|
The seams are in great shape
Not much filler needed.
|
|
Naumoff
Sat July 23, 2005 3:20am
Rating: 10
|
First Aid dashboard
Needed a box to mount the ignition switch. This old First Aid box was handy.
|
|
Brent Mills
Wed August 31, 2005 10:33pm
Rating: 10
|
Fiat Abarth
I've owned the Fiat since I was 16, sold it once because I needed money, and bought it back two years later from the same guy.
|
|
speed220mph
Thu April 20, 2006 10:36am
Rating: 10
|
When you're up the creek
We've all needed a paddle when we've been there.
|
|
vettestr
Wed May 24, 2006 8:46am
Rating: 10
|
383 small block. big or small no MODS needed
engine sitting in the frame on stock mounts
|
|
