boxhead
Sun January 2, 2005 1:39am
|
DSC00008
Here is my engine wireing loom with the connectors I dont need removed but still with wires in place
|
|
RobV
Mon June 13, 2005 7:20pm
|
Organizing the wiring for the gauges
I found it easiest to wire the dash and tape the wires in place on the dash to organize the loom in the dash area. I planned to add speakers under the dash and needed to make sure there was room.
|
|
jeffko
Tue November 22, 2005 10:12am
Rating: 10
|
Plug Wires
Upped the heat range on the plugs, added boot protectors and wire guides.
|
|
fastraxsg
Sat December 3, 2005 4:51am
|
Jan_2002b
Engine bay when we first viewed the car. At that time it had a 2273 cc six and a million wires and hoses, some just dead ending in space
|
|
Dirtrich
Tue February 21, 2006 7:43pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker 505hp build sheet...
• Blue printed machined 351W version Early Casting Block ('69) with Block Girdle Installed
• Scat Forged Steel 4.100 Stroke Crankshaft
• H Beam Rods 6.200" - ARP HD Rod Bolts
• Power Forged 10.5 to 1 Flat Top HP Pistons
• J & E Chrome Moly Ring Set
• Heavy Duty Double Roller Dynagear Timing Set
• Comp Cams Hydraulic Roller Retrofit Camshaft
• Clevite H series Racing Bearings
• Polished Edelbrock Victor Jr. cylinder heads
• Chrome Moly Hardened pushrods
• High Intensity Scorpion True Roller Rockers
• Melling HV Oil pump with Hardened FMS Drive Rod.
• Complete Fel-pro Gasket set
• Heavy Duty Harmonic Balancer
• New SFI Approved 10.5 inch Standard Flywheel
• Aluminum Timing cover
• Aluminum Finned Ford Racing Valve Covers
• New Fuel Lines and Gas Filter
• Polished Edelbrock Vic Jr. Single Plane
• Edelbrock 800 cfm 4 barrel w/ electric choke
• Elec Accel Billet Distributor & high voltage Coil
• High Flow Polished Aluminum Water & Fuel Pump
• Champion Spark plugs w/ 8mm ACCEL Spiral Wires
• New Chrome Thermostat Housing
• Oval aluminum finned air cleaner w/ Cobra logo
• Chrome 100 amp. Alternator and Polished Brackets
• March Pulley Setup with Serpentine-Belt
|
|
fastraxsg
Sat February 25, 2006 12:56am
|
Trunk
Fuel Cell and battery located in trunk, wooden box is rat's nest of wires to relocate...
|
|
HSSS427
Wed April 19, 2006 10:05am
|
ERA #414 427 side oiler after Keith Craft rebuild
427 side-oiler - C5AE-H
Shelby American aluminum heads, stage II port and polish
Forged crank C5AE-6300
Lemans Rods
Aluminum Police Interceptor intake - C6AE-9425-E
Mighty Demon 750 carb
Diamond Pistons
MSD 6AL electronic ignition and billett distributor w MSD 8.5mm wires
Comp Cams hydraulic roller camshaft: 242 duration, .645 lift, 248 duration, .635 lift
Crane lifters, Smith Bros push rods
|
|
Full Throttle Al
Sat July 29, 2006 2:21pm
Rating: 10
|
New MSD wires installed 1
New MSD 8.5mm Super Conductor wires for hemi heads installed to replace the red set.
|
|
Full Throttle Al
Sat July 29, 2006 2:21pm
Rating: 10
|
New MSD wires installed 2
New MSD 8.5mm Super Conductor wires for hemi heads installed to replace the red set.
|
|
Full Throttle Al
Sat July 29, 2006 2:21pm
Rating: 10
|
New MSD wires installed 3
New MSD 8.5mm Super Conductor wires for hemi heads installed to replace the red set.
|
|
Full Throttle Al
Sat July 29, 2006 2:21pm
Rating: 10
|
New MSD wires installed 4
New MSD 8.5mm Super Conductor wires for hemi heads installed to replace the red set.
|
|
Full Throttle Al
Sat July 29, 2006 2:21pm
Rating: 10
|
New MSD wires installed 5
New MSD 8.5mm Super Conductor wires for hemi heads installed to replace the red set.
|
|
cobra522
Sat September 2, 2006 2:05pm
Rating: 10
|
xtreme flow,Taylor wires, Custom fabbed billet valve covers
|
|
Thomas Lederer
Thu January 4, 2007 2:20am
|
Austrian nonkit Cobra
I hate wires!
|
|
cobrajam
Sun April 6, 2008 8:48pm
|
Unnamed wiring harness from CC advertiser
Box of wires. No instructions.
|
|
