Jackoboo
Fri December 15, 2006 9:04pm
|
DSCN0015
Me sealing footboxes with silicone and finish wiring dash
|
|
nanard289
Mon February 26, 2007 1:48pm
Rating: 10
|
Tea time 2
Step 2 consists to separate both tea balls and to fix them with silicone sealent on your air horn to avoid to swallow some gravels. Cheap and easy way to secure your engine
|
|
fastraxsg
Fri June 15, 2007 8:01am
|
Rear disk
Toyota disk added to rear in place of Holden drums, new shaft seals and u-joints
|
|
David Kirkham
Sat June 30, 2007 11:36am
Rating: 10
|
sealing_the_firewall_1_Medium_
|
|
David Kirkham
Sat June 30, 2007 11:36am
Rating: 8.66667
|
sealing_the_firewall_2_Medium_
|
|
David Kirkham
Sat June 30, 2007 11:36am
Rating: 10
|
sealing_the_firewall_3_Medium_
|
|
martrogers
Fri February 29, 2008 9:42pm
|
Bonnet Lip Milling Tool
The bonnet lip was variable thickness which made fitting a seal rubber difficult. This tool was lashed up by fixing a metal guide to a drill with Jubilee clips and using a milling bit. Worked very well as can be seen form the amount of fibreglass swarf.
|
|
Z-linkCobra
Mon November 2, 2009 11:08am
|
Passanger side.
Try to seal your mold as best you can with duct tape you will get some leakage but not to worry...it comes off with a little effort from the prybar....lol.
|
|
cobrajeff
Tue December 22, 2009 8:07am
Rating: 10
|
Heat shields added
I glued 3/4" foam insulation to the floorboards, and then sealed it off with sheet aluminium.
|
|
rdc767
Tue March 16, 2010 6:08pm
|
bulb sealradiator
bulb sealradiator
|
|
Wbulk
Fri May 7, 2010 11:44am
Rating: 10
|
Ball Joint Seal Ring
This is a Fix for A Arms that use the Chrystler ball joint without a seal groove machined in. This one was from B and B. A 3/16" steel ring was added to accept the ball joint seal. It was tack tig welded on the outside edges. The rings were cut on a water jet by Kirkhams Motorsports. Barry McGill can also do the fix.
|
|
Wbulk
Sun May 9, 2010 9:03am
Rating: 10
|
Ball Joint Seal Ring
A fix for A Arms shipped without the ball joint seal groove machined in. Ring added to accept a Chrystler Ball Joint Seal. The 3/16" thick rings were cut on Kirkhams Motorsports water jet. Barry McGill can also do the fix. The bad thing was B&B sent me the wrong arms that I paid to get fixed.
|
|
jcraigau
Tue June 15, 2010 7:14am
|
Rear Hubs
Painted with silver to seal the aluminium
|
|
kitcarbp
Thu October 14, 2010 7:36am
Rating: 10
|
stat o seal for fuel cell filler plate bolts
stat o seal for fuel cell filler plate, lifetime seal , no need to fuss with leaks ever again, expensive but permanenet and reuseable.
|
|
52chevyred
Fri April 29, 2011 10:35am
|
Cobra visit at Jodeco Auto Body
Here is my Cobra in primer at Jodeco Auto Body. Bruce said the body was in great shape and didn't take a lot of work. They are about to seal the primer.
|
|
