Pete Munroe
Wed July 22, 2009 9:58pm
Rating: 10
|
ERA 289 FIA shoulder harness mount
Roll bar mount for raising the shoulder harness. Moved one of the belt anchors to the outside of the roll bar. For the inside anchor I welded a bracket on the bar. Point was to be symmetrical to where I mounted the seat. Did not mount the seat as suggested in the "offset" position. Wanted it directly back from the pedals. Did lose some leg room by not doing the normal "offset".
|
|
TWOOD
Sun September 13, 2009 2:00pm
|
Trunk weather strip
Finished installation. Not very pretty, but using the larger dia. bulb wopuld not compress easily enough to permit the trunk to latch and allow the deck to be flush with the adjacent body. The original dia. weatherstrip did not compress along the top and sides at all.
|
|
Z-linkCobra
Mon October 19, 2009 1:58pm
|
Build pics
Did not like the leaf springs at all. This was a viable solution.
|
|
NZCOBRA
Fri December 4, 2009 12:38am
|
Bummer
they didn't give way, (yield)
|
|
SunDude
Mon January 25, 2010 8:03am
Rating: 10
|
Toy car view of my Superformance Cobra
Don't know how he did it, but my brother-in-law managed to make my Superformance Cobra look like a toy car. Cool.
|
|
Z-linkCobra
Thu February 18, 2010 8:25am
|
hood support close up.
Here you see the steel threaded collars pressed into the 5/8's holes. I didnt want to thread the aluminum for fear of the threads possibly pulling through.
|
|
Beejay
Mon April 26, 2010 4:29am
Rating: 10
|
Cobra Rebuild
Where did that clutch bolt go?
|
|
Dangerous Doug
Mon April 26, 2010 9:26pm
Rating: 10
|
Me and Cameron pick up the ERA 289FIA
Freshly painted ERA 289FIA rolled out. Ken's did an outstanding job on the wet-looking gloss black.
|
|
52chevyred
Mon May 3, 2010 3:35pm
|
Street Beast Shelf Surgery
Here's some surgery we did to drop the body down.
|
|
Dangerous Doug
Thu May 13, 2010 9:37pm
Rating: 10
|
ERA 289FIA Cobra First Drive and fully sorted
This is the day of my first drive after getting my Cobra back from paint and reassembling it. I took a vacation day off from work, and did a 12-hour blitz to reassemble it. This photo was my first drive right after the blitz. DD
|
|
Wbulk
Sat August 14, 2010 10:34am
|
Trunk Latch Modification on a B and B
This made it so I did not have to grind out the lip of the trunk for the latch finger, and by moving the latch down the license plate will now fit. I will add a rubber cushion to the trunk stop.
|
|
Z-linkCobra
Mon October 11, 2010 6:21am
|
Filter mount
Took a peice of 2" aluminum pipe and made this filter mount. The filter slides in and there are 2 set screws on either end ring to hold the filter in place. I didnt like the way the band clamps looked.
|
|
52chevyred
Fri April 29, 2011 10:35am
|
Cobra visit at Jodeco Auto Body
Here is my Cobra in primer at Jodeco Auto Body. Bruce said the body was in great shape and didn't take a lot of work. They are about to seal the primer.
|
|
52chevyred
Fri May 13, 2011 11:00am
Rating: 10
|
Cobra Painted by Jodeco Auto Body
This is my "Speedway Blue Metallic" paint PPG 81P with white stripes. Bruce Bunn and the guys at Jodeco did a great job again.
|
|
cobrajeff
Sat June 4, 2011 4:57am
Rating: 10
|
IMG_5913_Large_
The red T'Bird in the center is a restoration project I did for a fellow Ford retiree. he biught this car NEW!
|
|
