kitcarbp
Fri February 27, 2009 8:17am
Rating: 10
|
Fuel Line -Hard Tube Steel Adapter to 6 AN Flex Line
To ensure I use all steel, I had to use different vendors, Aeroquip hard tube compression fitting and Earls Auto fit hose end, Russell fuel hose, but all coated steel material for a reliable leak free fuel connection. This is intended as a street application so NO aluminum line is used. Remember, aluminum hard line may not be D.O.T. legal for the steet in your State!!
|
|
Ken Williams
Tue March 3, 2009 5:18pm
|
At Operation Comfort
Some of the Texas Cobra Club members went to a Ranch south of San Antonio where disabled Vets from Brooks Army Hospital are being rehabilitated. We gave rides and donated some tools
|
|
"Q"
Tue March 3, 2009 8:24pm
Rating: 10
|
What a great morning for a drive.
Cobra's from South Africa
|
|
kitcarbp
Fri March 6, 2009 7:29am
Rating: 9
|
Ford_Raditor_Heat_Rejection_Chart- Street Rod Example
This chart compares the heat rejection rate (cooling capacity) of three different types of radiators tested on an old Ford Street Rod. Coolant flow rate is held constant at 7 gpm (typical flow at idle perhaps, not sure where its being measured ???). It graphs the heat rejection for each radiator versus air flow through the radiator core. It is comparing 3 diff rad designs/materials at different CFMs through the core. The more air flow you have for a given coolant flow rate (7 gpm in this example) , the higher the heat rejection, basically linear in this example. The author of this graph is most likely selling the high efficiency radiator showing the improvement over the other two designs. To sum it up, the radiator at the top of the chart appears to be the most efficient at a low coolant flow rate (7 gal/min) over all air flows tested. Ya see how important rad core/tank design is? I learned something here.
|
|
steeler
Sun March 8, 2009 4:12pm
Rating: 10
|
|
steeler
Sun March 8, 2009 4:13pm
|
|
Clois Harlan
Mon March 9, 2009 6:32pm
|
Coupe from the side
Bryan Anderson of B&B has done such a wonderful job on the finish of the body...Just wait until we get some paint and some very high end gauges...on the inside.
|
|
Bri
Mon March 23, 2009 12:15pm
|
Lift1
A lift I built so I could get started.
|
|
63mercury
Thu April 2, 2009 8:12pm
|
My Cobra build
The FFR dash dosen't work so I had another blank made and will get it laser cut out on friday 04/03/09
|
|
DocDirk
Wed April 8, 2009 7:27pm
|
Rear of lower link arm
This looks like it will bind if the axle moves up at all, will probably have to be rounded off. The arm has two welded bends in it so I doubt I can replace it accurately with a tube.
|
|
rbutton
Thu April 9, 2009 9:48pm
|
First Phillips 66 station in McLean, Tx
Stopped by for some gas BUT seems they closed about the 1960's ... figures am always a little late!
|
|
rbutton
Thu April 9, 2009 10:07pm
|
KimsChristmasCard
Ever so often you get to meet some one "nice"
Miss Arkansas
|
|
kitcarbp
Fri April 17, 2009 8:27am
Rating: 10
|
air_Oval_filter_side_view9
Now here is a "think outside the box" solution. Not mine, but I found this unique solution posted here on CC.
|
|
lovehamr
Wed April 22, 2009 4:13pm
Rating: 10
|
The photo below captures a trend that is beginning to affect wildlife in th
Anticipating the Obama stimulus package, animals that were formerly self-sufficient are already modifying
their behavior to take advantage of what they expect to be a new set of societal norms in the next four to
eight years. This black bear from Montana has ceased hunting for a living and is sitting outside the US Fish
& Wildlife Service office in Kalispell, apparently waiting to be fed and to have his winter den dug by
government employees. The residents of Kalispell are calling him Bearack Obama.
|
|
DocDirk
Sat April 25, 2009 1:13pm
Rating: 10
|
Invisible grill
Grill painted black looks like the "Open front" look I like so much.
|
|
