Aussie Mike
Wed April 7, 2004 6:20am
|
New Wheels
Ozwheel Pin drive wheels finally fitted.
|
|
Chris Brown
Tue April 13, 2004 3:50am
Rating: 10
|
|
Rick Bagley
Tue May 4, 2004 5:59am
|
Oil Filer Mount
Canton Remote Oil Filter Mount using Braider Fabric/Rubber Hoses and AN fittings.
|
|
Bruce Edwards
Thu May 6, 2004 3:53pm
Rating: 10
|
Bill's 351W front 2
Another picture of Bill's 351W (TampaFla) for his 289 ERA.
Somethings you do not see but that I will post when I get more time.
Forged Keith Black pistons .30, Double row timing set, .10/.10 crank, Hand fit Sealed Power 1/16 moly rings, trimetal Clevite 77 bearings, HP/HV Melling pump with a HD drive, Edelbrock Performer RPM cam, Roller tip rockers, Brass freeze plugs, Windage tray, Oil pan baffle welded into bottom of pan, Oil temp bung brazed to side of pan, High Rev anti pump up lifters, ARP Studs for mains,ARP rod bolts, modified oil pick up, treaded front oil galley plugs, matched block oil passage to oil pump and FelPro gaskets
|
|
Art Burtt
Fri May 7, 2004 7:20am
Rating: 10
|
Tight Fit
Garage is just long enough to close the door
|
|
nanard289
Tue May 18, 2004 6:40am
|
aluminum transmission shaft
It is an alum trans shaft (from a Mustang car) cutted and welded to fit to good Cobra length. Then you have to adapt the right slipping yoke (with the special U joint) to fit on the gear box output.
|
|
Aussie Mike
Tue June 1, 2004 11:45pm
|
Hydratrak diff conversion
Modified the chassis to fit the 3.9 hydratrak diff.
|
|
Aussie Mike
Tue June 1, 2004 11:50pm
|
New diff fill plug
I machined the dif rear cover to fit a fill plug then I bored and slieved the rear cross member to give me access to it. the original Ford diff had the fill plug in the housing but this new diff doesn't have one.
|
|
simon clemens
Tue June 22, 2004 6:29am
|
sump shortening fitting section
|
|
simon clemens
Sun July 11, 2004 8:46am
|
Extractor_1_half_piped
That pipe will fit about there.
|
|
Full Throttle Al
Sat July 17, 2004 7:02am
Rating: 10
|
CSX4083
The One and Only "Cammer Cobra". Fitted with a NOS 427SOHC with 4 Weber setup.
|
|
boxhead
Sat July 24, 2004 2:43am
|
R/H rear spring/shockie
Here is a pic of the R/H rear spring/shockie assy that i fitted today
|
|
boxhead
Sat July 24, 2004 2:49am
Rating: 10
|
Wrong control arms
No matter what I tried there is no way the spring is going to fit without fouling the upper control arm.
|
|
boxhead
Sat July 24, 2004 2:53am
Rating: 10
|
Rear suspension completed
Here it is standing on its own with working rear suspension, I have also fitted the B&M shifter into the modified gearbox position (thanks Mike)
|
|
wilf leek
Sun July 25, 2004 9:04am
Rating: 10
|
No Sidepipes!
These are the lines you miss once you fit those vulgar sidepipe thingies.
|
|
