bmeyer29
Mon March 2, 2009 1:58pm
Rating: 10
|
351W after Kirkham surge tank pix1
NOTE: I replaced the two hose adapters in the tank with brass plugs
|
|
bmeyer29
Mon March 2, 2009 1:58pm
Rating: 10
|
351W after Kirkham surge tank pix2
NOTE: I replaced the two hose adapters in the tank with brass plugs
|
|
bmeyer29
Mon March 2, 2009 1:58pm
Rating: 10
|
351W after Kirkham surge tank pix3
NOTE: I replaced the two hose adapters in the tank with brass plugs
|
|
bmeyer29
Mon March 2, 2009 1:58pm
Rating: 10
|
351W after Kirkham surge tank pix4
NOTE: I replaced the two hose adapters in the tank with brass plugs
|
|
rokndad
Sat March 28, 2009 12:07pm
|
|
kitcarbp
Mon April 13, 2009 6:36am
Rating: 10
|
Modified Lower Radiator Hose
Here is the modified lower hose to keep the surge tank on the LOW pressure side (water pump inlet) of the system. Not the most elegant but very functional. I found a glass filled nylon "T" taht is 1.75" and has a 1.0" fill line for the surge tank.
|
|
kitcarbp
Mon April 13, 2009 7:01am
Rating: 10
|
Lower Rad Hose with "T"
Here is a close up of the "T" installed in the lower hose.
|
|
Garage10
Sun April 19, 2009 10:37pm
|
bottom left output side
installed a 5/8 hose barb on rads outlet to water pump from surge tank.
|
|
Garage10
Sun April 19, 2009 10:37pm
|
rad
Notice the 5/8 hose barb on the upper right. That was being fed from surge tank. I will plug it and now go to outlet to water pump instead.
|
|
DocDirk
Sat April 25, 2009 1:13pm
|
Rat's nest
Hoses to and from the surge tank.
|
|
DocDirk
Sat April 25, 2009 1:13pm
|
Auto Tranny vaccum origin
I put the auto tranny vacuum hose on this 1/8" vacuum outlet because it matches the modulator intake at the tranny - both are 1/8" size. Larger vacuum at the back of the carb I used for the brakes alone.
|
|
Pete Munroe
Wed July 22, 2009 9:58pm
Rating: 6
|
Canton oil thermostat
ERA 289 FIA with Canton oil thermostat. This is the drivers side hose run to the cooler.
Off-set the Canton thermostat cooler line outlets by taking it apart and rotating the segments. The segments can "clocked" in 90 degree increments, so the oil cooler hoses can exit on opposing sides. Made plumbing a lot easier in this installation. Fewer angles in the swivel fittings helps avoid any restriction on oil pressure.
|
|
Pete Munroe
Wed July 22, 2009 10:07pm
Rating: 10
|
ERA 289 FIA Canton oil thermostat
Canton oil thermostat installation, right side hose run up to the oil cooler
|
|
Pete Munroe
Wed July 22, 2009 10:12pm
|
ERA FIA Canton oil thermostat, top view
oil thermostat from the top showing some of the hose runs
|
|
Wbulk
Thu July 30, 2009 12:56pm
Rating: 10
|
Kirkham Alternator Bracket on a B and B
Reasonably priced bracket that allows the alternator to be mounted between the frame and out of the way of the upper hose. I think I paid $50 from Kirkham Motorsports.
|
|
