Fox
Mon August 2, 2004 7:53pm
Rating: 10
|
|
Anthony
Sat August 7, 2004 11:35am
Rating: 10
|
Algon mechanical fuel injection for ford 427 MR
This is a mechanical fuel injection system made in the 1960's, hilborn style, constant flow - low pressure. It has 1 7/8" throttle bores, close to 48mm. This intake was also made with the throttle bores straight up, as opposed to at a 45 degree angle like this one. Probably a good start for an electrical fuel injection conversion. As there are no venturi's, it should flow better than 48IDA's, about 30% better.
|
|
Anthony
Sat August 7, 2004 11:41am
Rating: 10
|
Algon fuel injection for ford 427 MR
This is a mechanical fuel injection system made in the 1960's, hilborn style, constant flow - low pressure. It has 1 7/8" throttle bores, close to 48mm. This intake was also made with the throttle bores straight up, as opposed to at a 45 degree angle like this one. Probably a good start for an electrical fuel injection conversion. As there are no venturi's, it should flow better than 48IDA's, about 30% better.
|
|
Anthony
Sat August 7, 2004 11:51am
Rating: 10
|
1960's Tecalemit-Jackson fuel injection system for road racing
This fuel injection system was developed in England in the 1960's, primarily aimed at road racing, as opposed to Hilborn/Algon which was more for drag racing. Tecalemit-Jackson apparently had a better partial throttle metering system for road racing, but because it was a continuous flow/low pressure, it didn't develop the max power as good as the Lucas - high pressure sequential fuel injection system that had better fuel atomization, more power. None the less, it still was used, and I heard it was at least tested in GT40's. Holman-Moody was the US distributor. The throttle bodies were based off of the weber 48 IDA, and could be bolted on any weber 48IDA intake, each throttle body separately.
|
|
Joe Guentert
Sun September 26, 2004 8:02am
Rating: 10
|
Supercharger
ATI-Procharger fitted to engine. Set up for 9PSI boost pressure. Has to CAD lots of special bracketry to fit under standard Cobra hood.
|
|
Secret Squirrel
Tue November 16, 2004 12:54pm
Rating: 10
|
Throttle Cable & Sensor Lines.
Lokar SS throttle cable, oil pressure line and coolant temperature sensor installed, 11/14/2004.
|
|
Michael C Henry
Tue December 14, 2004 9:23am
Rating: 10
|
top_rt_foot_box
Holley dead end fuel pressure regulater Y .Old wiper motor didn't self park . Voltage regulater and starter soleoid gave up when system was changed. The outside head stud w/Dove rocker anchor for shaft end support. Notice heat sheild thin aluminum and 1/2" thich foam w/ foil inside layer
|
|
Michael C Henry
Sun January 16, 2005 5:58pm
Rating: 10
|
Complete tensioner and windsheild anchor
The tensioner is used if you are using a convertable top.Air pressure will try to lift the top wnidsheild frame off the glass.
|
|
Sal Gerace
Thu May 5, 2005 9:00am
|
DSC02858
FE Pressure Plate
|
|
Sal Gerace
Thu May 5, 2005 9:01am
|
DSC02860
FE Pressure Plate
|
|
nanard289
Mon May 23, 2005 12:01pm
|
Fuel pressure regulator
fuel pressure regulator is adapted (via a 10AN fitting) directly on the fuel filter
|
|
simon clemens
Tue August 23, 2005 5:26am
|
Dash & Warning Light Sets, BUY here !!!
Custom Warning Lights - Engine Check (for any fault code on ECU)
Oil Pressure
L & R indicators
High beam
Seatbelt Warning (ADR necessary for all new cars)
Brake fail
Park brake
Ignition
Contact me if you would like a set of these lights for your self, I have plenty! send email or PM.
Full set $117, will be posted by certified mail, in a well padded package + additional information.
Over sea's customers welcome!
|
|
lineslinger
Fri September 9, 2005 2:34pm
Rating: 10
|
109_0981
expansion tank pressure tested and ready to go
|
|
simon clemens
Mon October 31, 2005 6:15am
|
Fuel Filler Neck Complete
Custom fabricated aluminium filler neck, constructed from old bull bar sections. Will be pollished at a later date. Pressure tested with no leaks.
|
|
HSSS427
Sat February 25, 2006 10:22am
|
Mcleod pressure plate and clutch for sale
|
|
