TWOOD
Mon September 1, 2008 3:51pm
|
SAME BRACKET BACK TO BACK
Assuming that the reatangular side should be placed on the frame and the "ears" ar ewhere the control arms mount.
This would place the left and right control arms in different planes and not parallel to each other.
The rectangular side has a interference with the shock tower and the mounting holes do not align and not adjustment is possible.
|
|
TWOOD
Mon September 1, 2008 3:51pm
|
Same bracket back to back with irregular side on frame
This position permits the irregular ear side of the bracket to fit around the shock tower and any of the holes can align with the slots in the frame.
|
|
bannishg
Tue November 11, 2008 6:43pm
Rating: 10
|
Hemmings Motor News, April 1986
This is CSX-2321. It found its next owner the following month. 27 years later (as of 2013) it is still in the same hands.
|
|
Michael J
Fri January 2, 2009 5:14pm
Rating: 10
|
Daily Driver
A street driven small block car seen at the Steamboat Springs, CO. vintage races in 1994. This same car appeared at the 1998 Steamboat races painted red. (They both had the same license plate.) Possibly it is CSX 2545.
Contact me at lightcatcher@bresnan.net for more details.
|
|
Russ Dickey
Tue January 6, 2009 7:36am
|
Andy Samberg at his best
J.I.M.P. video
|
|
n6opv
Thu January 22, 2009 11:23pm
|
Arntz tranny tunnel
Shown here is the removable section of the tranny tunnel. With the big engine setback in all the Arntz / Butler cars, you can remove the transmission while seated if you desire. Only a few very late Butlers had this and all Arntz Type 4 cars. I have no idea what the many cutouts are for  Also shown are the two triangulation tubes that connect the center of the cowl hoop to the 2 main frame rails for increased rigidity. The 3rd leg of the roll bar (not shown) also attaches to the same point on the passenger side frame rail. This is Arntz Type 4 only as well.
|
|
fkemmerer
Thu May 14, 2009 6:59am
|
AFR1
Sample AFR table for an EFI FE. NOTE THAT NO ONE SHOULD COPY THIS TABLE AND JUST USE IT - THESE SETTINGS ARE NOT APPROPRIATE FOR EVERY MOTOR AND WHAT WORKS FINE IN MINE MAY VERY LIKELY DAMAGE YOURS.
|
|
fkemmerer
Thu May 28, 2009 6:05pm
|
Cranking Fuel Table for 482 ci FE with TWM Injections
Sample cranking fuel table table for an EFI FE. NOTE THAT NO ONE SHOULD COPY THIS TABLE AND JUST USE IT - THESE SETTINGS ARE NOT APPROPRIATE FOR EVERY MOTOR AND WHAT WORKS FINE IN MINE MAY VERY LIKELY DAMAGE YOURS.
|
|
bran3b
Sat June 20, 2009 9:26pm
|
bumper damage
Same stupid Avalanche bumper did this.
|
|
hogster
Sat June 27, 2009 11:06pm
|
Added Filler Rod
Same procedure with the filler rod
|
|
jdean
Sun June 28, 2009 12:21pm
Rating: 10
|
|
jdean
Sun June 28, 2009 5:47pm
Rating: 10
|
|
Bernica
Fri December 18, 2009 7:50pm
Rating: 10
|
Old 101 vs New 101
Left is new 101 octane; Right is same only 11 mos old
|
|
63mercury
Fri January 1, 2010 11:22am
|
|
Z-linkCobra
Thu February 18, 2010 8:25am
Rating: 1
|
Hood hinge support
Same thing on the hood. I am going to glass in the aluminum frame so that its solid with hood.
|
|
