 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
1 |
2 |
3 |
| 4 |
5 |
6 |
7 |
8 |
9 |
10 |
| 11 |
12 |
13 |
14 |
15 |
16 |
17 |
| 18 |
19 |
20 |
21 |
22 |
23 |
24 |
| 25 |
26 |
27 |
28 |
29 |
30 |
31 |
|
|
CC Advertisers
|
|
Clois Harlan
Wed March 29, 2006 4:51pm
|
Picture 1 showing bell crank
|
|
Clois Harlan
Wed March 29, 2006 4:54pm
Rating: 10
|
Home made foot pedal and linkage to bell crank
|
|
LwCwb
Thu March 30, 2006 3:47am
Rating: 10
|
Caterpillar 3406BC
Picture of my first engine build up. From start to finish, it took me from the mid-october to mid-march, tearing the engine completely down, then checking oil clearances on all the Rods, pistons, crank journals, ect, then building her back up, then finally running the engine. I only worked on it for about an hour every day, give or take a few minutes. Taken at Cumperland Perry Vocational Technical School.
|
|
HSSS427
Wed April 19, 2006 10:05am
|
ERA #414 427 side oiler after Keith Craft rebuild
427 side-oiler - C5AE-H
Shelby American aluminum heads, stage II port and polish
Forged crank C5AE-6300
Lemans Rods
Aluminum Police Interceptor intake - C6AE-9425-E
Mighty Demon 750 carb
Diamond Pistons
MSD 6AL electronic ignition and billett distributor w MSD 8.5mm wires
Comp Cams hydraulic roller camshaft: 242 duration, .645 lift, 248 duration, .635 lift
Crane lifters, Smith Bros push rods
|
|
computerworks
Mon July 3, 2006 4:07pm
|
SAAC-31 - Cranky's Paddock
|
|
computerworks
Mon July 3, 2006 4:08pm
|
SAAC-31 - Cranky's Paddock
|
|
computerworks
Mon July 3, 2006 6:41pm
Rating: 10
|
|
computerworks
Mon July 3, 2006 6:41pm
Rating: 10
|
|
Morris
Thu September 21, 2006 8:01am
|
|
speed220mph
Thu March 1, 2007 6:44am
Rating: 10
|
427 side oiler bottom end assembly
Short section of hoses are slipped over main-cap studs to protect main-bearing journals when installing crankshaft. Note reinforcing strap on center main-bearing cap.
|
|
buildride
Thu March 1, 2007 11:55pm
|
1967 427 S.C. Cobra Viper Blue
1967 427 S.C. Cobra Viper Blue.Smeding 427 Cobra Special. Bored and stroked to 427 cu.in., 450hp 450ft lbs est., 10.2:1 comp. 351 SVO Sportsman II block 4.030” bore, 4340 forged crank 4.170” stroke, forged pistons floating pin, 4340 steel H beam rods 7/16 ARP bolts, engine balanced to ½ gram, roller cam .493/.510 lift 279/289 dur, Edelbrock Performer RPM aluminum heads 2.02/1.60 SS valves springs single w/damper, dual roller timing chain, aluminum roller rockers 1.6 ratio, Intake Edelbrock aluminum performer, Holley 600 four barrel, HEI dist, March serpentine billet aluminum pulley set.
|
|
STEVE POTTS
Wed May 2, 2007 11:31am
|
427 FE 4.25 stroke scat crank
|
|
westcott cobra
Sat July 21, 2007 2:58am
Rating: 10
|
nitrided 351C crank
Crank installed, looks grey from last nitriding
|
|
428street
Thu November 8, 2007 8:02pm
Rating: 10
|
428 Block with scat crank
|
|
cobrajam
Sun November 18, 2007 6:06pm
|
391 FT Steel Crank
knife edged and lightened, went from 75lbs to 65lbs, 3.78in stroke, .010/.010, machined snout and flywheel face to fit FE
|
|
|
All times are GMT -7. The time now is 01:15 PM.
Links monetized by VigLink |
