JLC800
Wed December 10, 2003 12:23pm
Rating: 10
|
IRS 3.54 power-lock
HD axles and swing arm
|
|
Rick Bagley
Thu January 1, 2004 8:58am
Rating: 10
|
Enclosed Trailer, 22'
22' X8' wide, United Expressline, 5,600lbs axles.
Good quality enclosed trailer.
|
|
blykins
Fri January 9, 2004 8:45am
Rating: 10
|
Getting ready to install axles and brakes
|
|
Rick Parker
Wed April 20, 2005 1:23pm
Rating: 10
|
Rear Axle Vent Tube & Filter
I found a formed hose that curved around the link bar perfectly.
|
|
bshap
Thu April 21, 2005 4:03am
Rating: 8
|
Estate sale
Here is a beautiful NEARLY NEW 1983 Cobra. Properly and carefully built from a WEST COAST COBRA kit, it is fitted with a Ford 460ci V8 engine. This beast has only gone approximately 8000 miles since completion. Always stored inside. The builder/collector/owner recently passed away and this is an estate sale. It has a Nascar Can-Am chassis with power rack and pinion steering; 11-inch vented rotors with 4-piston racing calipers; 4-bar rear axle with 9-inch drop-out center section; 25 gallon race-legal fuel cell; weight 2970lbs (50/50 front/rear). Available with or without a spare fully-rebuilt 460ci engine. Located near Toronto Canada. Pre-purchase inspections and/or appraisals are welcome. Hard to find a nicer example! Asking cdn$56,000.00 (us$45,000) OBO Contact Bob Shapton 519-927-3966
|
|
simon clemens
Wed April 27, 2005 7:00am
|
3 Position Height Bracket
3 Position suspension height bracket on lower coilover eyelet.
12 Position dampen rate on 'QA1' shock. Plus adjustable spring tension.
Shortened BW Diff.
New 28 spline axles.
New 3.73:1 gear set.
New 4 pinion LSD assembly.
|
|
simon clemens
Wed April 27, 2005 7:00am
|
4 Link & Panhard
4 Link & Panhard, top adjustable trailing arms.
Shortened BW Diff.
New 28 spline axles.
New 3.73:1 gear set.
New 4 pinion LSD assembly.
|
|
simon clemens
Wed April 27, 2005 7:00am
|
LHS Axle, 'QA1' Coilover
Shortened BW Diff.
New 28 spline axles.
New 3.73:1 gear set.
New 4 pinion LSD assembly.
3 Position suspension height bracket on lower coilover eyelet.
12 Position dampen rate on 'QA1' shock. Plus adjustable spring tension.
|
|
simon clemens
Wed April 27, 2005 7:24am
|
Brake relocation
Rear brake relocation was needed to allow clearance between the coilovers and the calipers. Re-drilled calliper mount bracket holes so the caliper sits about 40 degrees foward from original position. Also had to swap Left & Right brake assemblys to opposite sides, so the hand brake cable now will run on top of the axle & still be accuated by a foward movement. I wonder if others have thought of this solution?
|
|
W2zero
Sat May 14, 2005 8:14pm
|
FRPP rear disc, Dutchman axles
Narrowed nine inch, Detroit locker, 4.11 gears, Dutchman 31sp axles, FRPP rear disc brakes.
|
|
LMH
Wed September 7, 2005 12:34pm
Rating: 10
|
Rear suspension
Axle housing/Suspension installed. Awaiting axles and third member.
|
|
66rdster
Fri September 23, 2005 6:34pm
|
|
Herkypilot
Sat November 12, 2005 5:03pm
|
Axle_2
Remove these for Wilwood Big brake kit.
|
|
hogster
Sat June 10, 2006 3:26am
|
stainless tank
The stainless tank is in place, Diff just about fully done. I noticed bent axles in the donor and sourced a pair in Darwin. New bearings pressed on, a bit of paint and doesn't look too bad.
|
|
Shelboss
Tue December 5, 2006 10:04am
|
Early Contemporary trailing arms
Long trailing arms extended forward. These did not work because of the rear axle being solid mounted and the radius of the trailing arm fighting the lower control arm's path.
|
|
