bermblaster41
Fri November 17, 2006 12:02pm
Rating: 10
|
Wrights_036
My wife hopes the cobra will pull my interest from racing Motocross
|
|
GASKETBOY
Sun December 10, 2006 9:01am
|
Post - pull picture
The 390 after extraction. Room has now been made for a 428CJ.
|
|
Dennis Larson
Thu December 21, 2006 2:39pm
|
My Build
Ford crate 302 w/340hp, Holley Carb 670, Fortes pulleys
|
|
buildride
Thu March 1, 2007 11:55pm
|
1967 427 S.C. Cobra Viper Blue
1967 427 S.C. Cobra Viper Blue.Smeding 427 Cobra Special. Bored and stroked to 427 cu.in., 450hp 450ft lbs est., 10.2:1 comp. 351 SVO Sportsman II block 4.030” bore, 4340 forged crank 4.170” stroke, forged pistons floating pin, 4340 steel H beam rods 7/16 ARP bolts, engine balanced to ½ gram, roller cam .493/.510 lift 279/289 dur, Edelbrock Performer RPM aluminum heads 2.02/1.60 SS valves springs single w/damper, dual roller timing chain, aluminum roller rockers 1.6 ratio, Intake Edelbrock aluminum performer, Holley 600 four barrel, HEI dist, March serpentine billet aluminum pulley set.
|
|
1985 CCX
Wed March 21, 2007 6:34pm
Rating: 10
|
Starting to install hubcentric adapters from Vintage Wheel on the CCX
My how the dust settles over and under the car during the winter. Pulled the cover back to start installation of Vintage Wheel pin drive adapters. These parts have been machined prior to shipping to fit perfectly on the Jaguar spindle. Spinners are forged / polished and include Vintage Wheels Safety:Anti-Theft option. This option will not allow spinner to come off without removal of the safety pins.
|
|
Anthony
Sun May 20, 2007 6:03pm
Rating: 10
|
1978 Cobra Jet Jet Boat
Boat manufactured by company called Cobra Jet. 18 ft long, shallow V-Hull. 460 Ford, tunnel ram, berkley jet pump drive.
The boat accelerates like a high performance car, unbelieveable. Great boat for water skiing. The only boat I've ever only needed to give it part throttle to pull up a skiier. Full throttle will rip you arms off. With full throttle, the boat will accelerate so hard, it leaps out of the water before the skier gets even half out of the water, and you have to let go at that point.
The boat is easy to trailer, to launch, to load on trailer, etc. The best boat I have ever owned. Easiest boat to use, most fun with lowest maintenance.
Kind of like a cobra, but on the water.
|
|
Bunkie314
Thu June 7, 2007 10:28pm
|
On the Dyno
Break in and pull tests.
|
|
Bunkie314
Thu June 7, 2007 10:28pm
|
On the Dyno
Break in and pull tests. Everything went well. Peaked 560 HP and 500 ft-lbs.
|
|
Bunkie314
Thu June 7, 2007 10:28pm
|
On the Dyno
Break in and pull tests. Everything went well. Peaked 560 HP and 500 ft-lbs.
|
|
Ls6venom
Tue July 10, 2007 6:09pm
Rating: 1
|
6-25-2007-021
Pulling in to the hotels.
|
|
Ls6venom
Tue July 10, 2007 6:09pm
|
6-25-2007-023
Pulling in to the hotels.
|
|
Ls6venom
Tue July 10, 2007 6:09pm
|
6-25-2007-027
Pulling in to the hotels.
|
|
Ls6venom
Tue July 10, 2007 6:09pm
|
GTM
Pulling in to the hotels.
|
|
Rick Parker
Thu August 9, 2007 9:48pm
Rating: 10
|
48 IDA Webers
NOS manifold, center pull linkage, Italian IDA's on a real nice 289.
|
|
traindriver
Fri September 14, 2007 4:02pm
Rating: 10
|
A correct Weber linkage for a 351
This is a center bellcrank setup which works much better than the stock side pull design.
|
|
