Griffith
Mon October 18, 2004 4:08am
|
|
Griffith
Mon October 18, 2004 4:10am
|
Cobra Bell Housing - Inside
|
|
Griffith
Mon October 18, 2004 4:12am
|
Cobra Bell Housing - Number
|
|
Secret Squirrel
Wed October 20, 2004 7:27am
Rating: 10
|
Clutch Slave Unit Install, See Description Note.
Clutch Slave Unit Installed on Bell Housing on 10/18/2004. Note: During drivetrain installation I discovered that the clyinder has to be rotated 180 degrees with the hose pointing downward.
|
|
Pete Munroe
Thu October 21, 2004 12:59am
Rating: 10
|
ERA 289 FIA #2027
Moved shifter to the "forward" position in the TKO housing. This is about same location as top-loader shift would be. Patch gives you an idea how far back shifter was before. Shifter is a piece from Mike Forte's shop. The doublers on the floor are for the seat mounting bolts.
|
|
Michael C Henry
Wed December 15, 2004 10:26pm
Rating: 10
|
adjustable secondary
this is a Quick Fuel Technology adjustable vacume secondary housing with a quick change spring cover added notice the needle screw ? it can change the opening rate
|
|
simon clemens
Mon April 11, 2005 5:07am
|
Rear end
Diff housing is shortened, & is waiting for coilover brackets to be welded into place.
|
|
Rodney
Sat May 21, 2005 12:19pm
Rating: 10
|
powder coated
powder coated intake, fuel log, expansion tank, valve covers and bell housing. new ceramic coated headers and short side pipes!
|
|
427orFIAisOK4me
Mon August 1, 2005 8:57pm
|
Blowproof Bell housing
House of Cobras 418
|
|
LMH
Wed September 7, 2005 12:34pm
Rating: 10
|
Rear suspension
Axle housing/Suspension installed. Awaiting axles and third member.
|
|
Dirtrich
Tue February 21, 2006 7:43pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker 505hp build sheet...
• Blue printed machined 351W version Early Casting Block ('69) with Block Girdle Installed
• Scat Forged Steel 4.100 Stroke Crankshaft
• H Beam Rods 6.200" - ARP HD Rod Bolts
• Power Forged 10.5 to 1 Flat Top HP Pistons
• J & E Chrome Moly Ring Set
• Heavy Duty Double Roller Dynagear Timing Set
• Comp Cams Hydraulic Roller Retrofit Camshaft
• Clevite H series Racing Bearings
• Polished Edelbrock Victor Jr. cylinder heads
• Chrome Moly Hardened pushrods
• High Intensity Scorpion True Roller Rockers
• Melling HV Oil pump with Hardened FMS Drive Rod.
• Complete Fel-pro Gasket set
• Heavy Duty Harmonic Balancer
• New SFI Approved 10.5 inch Standard Flywheel
• Aluminum Timing cover
• Aluminum Finned Ford Racing Valve Covers
• New Fuel Lines and Gas Filter
• Polished Edelbrock Vic Jr. Single Plane
• Edelbrock 800 cfm 4 barrel w/ electric choke
• Elec Accel Billet Distributor & high voltage Coil
• High Flow Polished Aluminum Water & Fuel Pump
• Champion Spark plugs w/ 8mm ACCEL Spiral Wires
• New Chrome Thermostat Housing
• Oval aluminum finned air cleaner w/ Cobra logo
• Chrome 100 amp. Alternator and Polished Brackets
• March Pulley Setup with Serpentine-Belt
|
|
RobV
Wed March 29, 2006 1:18pm
|
|
Mike Simard
Tue June 13, 2006 3:30pm
|
THERMOSTAT1
THERMOSTAT HOUSING
|
|
Mike Simard
Tue June 13, 2006 3:30pm
|
THERMOSTAT4
THERMOSTAT HOUSING
|
|
kitcarbp
Sun November 12, 2006 7:00pm
Rating: 10
|
Mr 460, Meets Ms. TREMEC
I used a 351M/400M bell housing from a retired Bronco.
|
|
