gman
Sun June 1, 2003 7:51pm
|
460 cubic inches
First Time My father ever touched an engine. Now he'll tell everybody he helped install it.
|
|
Cobra Chuck
Sun July 20, 2003 10:08pm
|
Under the hood
Another shot of the engine.
|
|
Cobra Chuck
Sun July 20, 2003 10:19pm
|
Engine nearly complete
Just finishing up the engine. Built it up from the block. Lot's of custom stuff
|
|
StephenC
Thu July 31, 2003 12:19pm
Rating: 1
|
Left Rear Quarter
Waitin' for an engine. Bill P. at SA will build a 427 to fill the hole under the hood.
|
|
Brett J. Bolte
Sun October 26, 2003 8:06pm
Rating: 10
|
11-30-02_engine_lo_res
Engine. Stroked 1966 427.
|
|
surfer44
Thu October 30, 2003 5:02am
|
66 428
Starting to look like an engine.
|
|
daltondavid
Fri May 14, 2004 11:52am
|
428 PI car#01428
Original Engine. Aluminum Radiator. MSD ignition Demon 750
|
|
BOND 007
Wed September 22, 2004 6:06am
|
Volkswagen Passat Variant TDI
I sold the Fiat Bravo and bougt thi Volkwagen Passat Variant TDI (96kw/130HP) with diesel engine. 6l diesel/100 km
|
|
Joe Guentert
Sun September 26, 2004 8:02am
Rating: 10
|
Supercharger
ATI-Procharger fitted to engine. Set up for 9PSI boost pressure. Has to CAD lots of special bracketry to fit under standard Cobra hood.
|
|
Rick Parker
Sun November 7, 2004 11:52am
Rating: 10
|
Remote filter & cooler plumbing
Oil goes out of the engine to the filter and then forward to the cooler then back into the engine. I intend to install a thermostat.
|
|
Scouder
Wed January 5, 2005 6:14pm
Rating: 10
|
Another Shot of the engine...
|
|
cobrajeff
Wed February 23, 2005 4:50pm
Rating: 10
|
Carroll Shelby Hall of Fame
New addition to my CS "Hall of Fame" - an all-aluminum 351 Cleveland engine.
|
|
bshap
Thu April 21, 2005 4:03am
Rating: 8
|
Estate sale
Here is a beautiful NEARLY NEW 1983 Cobra. Properly and carefully built from a WEST COAST COBRA kit, it is fitted with a Ford 460ci V8 engine. This beast has only gone approximately 8000 miles since completion. Always stored inside. The builder/collector/owner recently passed away and this is an estate sale. It has a Nascar Can-Am chassis with power rack and pinion steering; 11-inch vented rotors with 4-piston racing calipers; 4-bar rear axle with 9-inch drop-out center section; 25 gallon race-legal fuel cell; weight 2970lbs (50/50 front/rear). Available with or without a spare fully-rebuilt 460ci engine. Located near Toronto Canada. Pre-purchase inspections and/or appraisals are welcome. Hard to find a nicer example! Asking cdn$56,000.00 (us$45,000) OBO Contact Bob Shapton 519-927-3966
|
|
mloy
Sat July 16, 2005 2:00pm
|
Cobra Engine.
'86 5.0L engine. .030 over, forged pistons, X303 hydraulic roller cam, Edelbrock Performer aluminum heads, Cobra Intake, Open-letter Cobra valve covers. '65 front timing cover, new oil pan. Balanced and assembled by a NASCAR engine builder. Runs pretty good....
|
|
mloy
Sat July 16, 2005 2:00pm
|
|
