 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
1 |
2 |
3 |
4 |
5 |
6 |
| 7 |
8 |
9 |
10 |
11 |
12 |
13 |
| 14 |
15 |
16 |
17 |
18 |
19 |
20 |
| 21 |
22 |
23 |
24 |
25 |
26 |
27 |
| 28 |
29 |
30 |
|
|
|
|
|
|
CC Advertisers
|
|
|
55 result(s) to your search. (Ring)
|
Prev Page ·
|
|
Rick Parker
Fri December 27, 2002 9:28pm
Rating: 10
|
Rear End Setup
Ford 9" N case Traction lock, 3.70 Ring & pinion from Mark Martins #6 car with 500 miles testing.
|
|
wicked fast
Sun May 4, 2003 7:50pm
|
Shifter ring
4 speed shifter ring with
Ford logo.
Anybody have one ???
|
|
REDSC400
Thu November 6, 2003 5:17pm
Rating: 10
|
ERA 375 428FE Engine
Early photo (2003 December) of ERA375's engine, 1966 428FE from 1966 Thunderbird, fully blueprinted and balanced, 423HP at the rear wheels @ 5400 RPM, 450 Ft/Lbs torque at 3900 RPM. Holley 850 CFM Double Pumper Carb, Sidewinder Intake Manifold, Original Pent Roof Chrome Valve Covers with 427 Badges, Competition Cams 33-230-4 Cam, Dove Rocker support End Stands, 2.09" Intake and 1.75" Exhause, Milodon Circle Track 8 Qt oil pan, Forged A1 Pistons with SS-50 Rings, Forged Crank and Tie Rods, Auto Racing Products Head Studs, Crand Dual Stage Hydro Lifters, K&N Xstream Air Filter, MSD 6AL Igniton, Mallory Electronic Distributor with Magnecor KV85 Ignition Wires and Looms, High Pressure Oil Pump, Mallory Comp. Coil
|
|
FUNFER2
Wed December 17, 2003 1:49pm
Rating: 10
|
Custom fuel neck
Custom fuel filler neck going down to the fuel cell. Casted out of alum. Custom ring also.
|
|
EndiKarz
Tue March 2, 2004 6:07pm
|
Daily driver
Daily driven -
302 .030 over, forged pistons, factory bushed rods, F303 cam, ported factory heads 1.9 x 1.6 stainless steel/swirl polished valves, ported truck lower, Downs upper, roller rockers, ATI procharger 14 lbs. boost, MSD 6BTM, 190 LPH pump, 70 LPH T-rex, AOD 2600 stall converter, 3:73 ring & pinion, race craft suspension, subframe connectors
|
|
Bruce Edwards
Thu May 6, 2004 3:53pm
Rating: 10
|
Bill's 351W front 2
Another picture of Bill's 351W (TampaFla) for his 289 ERA.
Somethings you do not see but that I will post when I get more time.
Forged Keith Black pistons .30, Double row timing set, .10/.10 crank, Hand fit Sealed Power 1/16 moly rings, trimetal Clevite 77 bearings, HP/HV Melling pump with a HD drive, Edelbrock Performer RPM cam, Roller tip rockers, Brass freeze plugs, Windage tray, Oil pan baffle welded into bottom of pan, Oil temp bung brazed to side of pan, High Rev anti pump up lifters, ARP Studs for mains,ARP rod bolts, modified oil pick up, treaded front oil galley plugs, matched block oil passage to oil pump and FelPro gaskets
|
|
boxhead
Fri July 9, 2004 6:05am
Rating: 10
|
dismantled_engine
This is my engine all dismantled and ready to hone out for new rings and gaskets
|
|
Rick Parker
Sat July 10, 2004 9:38pm
Rating: 10
|
Could have been an Expensive Mistake
"O" Ring for remote filter mount.
|
|
Secret Squirrel
Wed November 3, 2004 9:35am
Rating: 10
|
T-5 Shifter With Ring & Boot
T-5 Shifter with trim ring and boot installed on 10/30/2004.
|
|
jeffko
Wed February 9, 2005 5:40pm
|
Getting Closer
crank, cam, rods, pistons, rings, bearings, timing chain, cover, water pump, blueprinted oil pump, the list is growing...
|
|
|
All times are GMT -7. The time now is 09:34 PM.
Links monetized by VigLink |
