fkemmerer
Sat September 1, 2007 7:57pm
Rating: 10
|
Injected Side Oiler
These are pictures of the engine that is going into my Cobra. Its is an all aluminum 427 FE Side-oiler that has been stroked to 482 ci. The motor was done my Keith Craft and it makes 655 hp, 633 ft-lbs of torque.
|
|
olddog
Tue September 4, 2007 7:39pm
|
|
fkemmerer
Sat January 19, 2008 7:57am
Rating: 10
|
Alum. FE with TWM EFI
I've added some of the accessories to my engine and changed the distributor to a FAST dual-sync to allow for individual cyclinder tuning. The engine was built by Keith Craft.
|
|
fkemmerer
Sat January 19, 2008 7:57am
Rating: 10
|
Alum. FE with TWM EFI
I've added some of the accessories to my engine and changed the distributor to a FAST dual-sync to allow for individual cyclinder tuning. The engine was built by Keith Craft.
|
|
fkemmerer
Sat January 19, 2008 8:46am
|
Dyno Sheet from 482CI EFI FE
The dyno sheet from Keith Craft for my engine.
|
|
fkemmerer
Sun January 20, 2008 10:23am
Rating: 10
|
Blown and Injected SBC
An example of the type of radical induction that can be run on the street with EFI. This is a 383 ci SBC which makes 625 HP on pump gas.
|
|
fkemmerer
Thu February 14, 2008 6:06am
Rating: 10
|
1963 Blown and Injected Corvette
These are some pictures of the 1963 Blown and Injected Corvette that I built a few years back. The car is basically stock except for the drivetain. The motor is a 383 stroker with a 6-71 roots supercharger and EFI.
|
|
fkemmerer
Thu February 14, 2008 6:06am
Rating: 10
|
1963 Blown and Injected Corvette
These are some pictures of the 1963 Blown and Injected Corvette that I built a few years back. The car is basically stock except for the drivetain. The motor is a 383 stroker with a 6-71 roots supercharger and EFI.
|
|
vector1
Thu May 22, 2008 3:20pm
|
jbl_trunk_001_Small_
finished jbl trunk ready for efi
|
|
fkemmerer
Wed July 16, 2008 11:32am
|
Rear Suspension and Fuel System
Pictures of ERA #753 in the final stages of assembly. This is the rear suspension with pin drive hubs. Note the fuel system components - polished fuel tank, electrical fuel pump, and inline filters.
|
|
fkemmerer
Wed July 16, 2008 11:32am
|
Electrical System for EFI and Ignition
Pictures of ERA #753 in the final stages of assembly. This shows the electrical components for the Electronnic Fuel Injection system and Ingition Box hidden under the dash.
|
|
fkemmerer
Fri July 18, 2008 7:10pm
Rating: 10
|
ERA #753 - Throttle linkage and cable
A picture of the completed throttle inkage and cable. All set to connect to a TWM throttle body EFI intake.
|
|
fkemmerer
Sun July 20, 2008 11:40am
Rating: 10
|
ERA #753 - Engine Ready to go in the car
This picture shows the final engine for ERA #753 ready to go into the car. All of the fittings, expansion tank, etc. are on.
|
|
fkemmerer
Sun July 20, 2008 11:40am
Rating: 10
|
ERA #753 - Engine Ready to go in the car
This picture shows the final engine for ERA #753 ready to go into the car. All of the fittings, expansion tank, etc. are on.
|
|
fkemmerer
Sun July 20, 2008 11:40am
|
ERA #753 - Engine Ready to go in the car
This picture shows the final engine for ERA #753 ready to go into the car. All of the fittings, expansion tank, etc. are on.
|
|
