mloy
Mon February 7, 2005 9:14am
Rating: 10
|
Front Uprights - Back side
The casting and machine quality is very high on these parts.
|
|
simon clemens
Fri March 18, 2005 4:14am
|
New Crank Pully
I had a crank pully custom made out of aluminium, the original pully had too many un-needed bits. I also wanted the power steering pump rpm reduced, so I had a smaller pully machined, this should also reduce some load on the engine 
|
|
Unregistered
Sat March 19, 2005 12:19am
|
Steering wheel hub
First steep, we have to cut a large aluminum slice and to machine it on the lath
|
|
cobrajeff
Wed March 23, 2005 9:26am
Rating: 10
|
Plastic Valve Covers
Here are two sets of plastic COBRA valve covers I made in the 70's. Thought the clear ones would really be cool. To really get the detail, I would have had to drill small air holes in them to get the vacuum machine to work well - I wasn't willing to do that.
|
|
phatry5
Sun April 17, 2005 10:13pm
|
Dash
All digital, with custom machined rings around each
|
|
jeffw
Sat April 30, 2005 8:32pm
|
Headed to Columbus
On display at the Precision Machine Tool Show - Columbus Convention Center May 2 - 5.
|
|
mickmate
Mon May 23, 2005 6:57am
|
Machining pedals
This set up worked well to machine the slots on the back of the pedal pads.
|
|
lovehamr
Thu June 9, 2005 8:38pm
|
Champions
The man and his machine
|
|
Tongue Pirate
Sat July 2, 2005 9:14pm
|
13" Short
Fresh Driveline Install
|
|
jdean
Sat August 6, 2005 7:07pm
Rating: 10
|
|
nanard289
Thu September 1, 2005 12:54pm
Rating: 7
|
shifter step 7
I have to machine a small button to move the reverse locker
|
|
Dirtrich
Tue February 21, 2006 7:43pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker 505hp build sheet...
• Blue printed machined 351W version Early Casting Block ('69) with Block Girdle Installed
• Scat Forged Steel 4.100 Stroke Crankshaft
• H Beam Rods 6.200" - ARP HD Rod Bolts
• Power Forged 10.5 to 1 Flat Top HP Pistons
• J & E Chrome Moly Ring Set
• Heavy Duty Double Roller Dynagear Timing Set
• Comp Cams Hydraulic Roller Retrofit Camshaft
• Clevite H series Racing Bearings
• Polished Edelbrock Victor Jr. cylinder heads
• Chrome Moly Hardened pushrods
• High Intensity Scorpion True Roller Rockers
• Melling HV Oil pump with Hardened FMS Drive Rod.
• Complete Fel-pro Gasket set
• Heavy Duty Harmonic Balancer
• New SFI Approved 10.5 inch Standard Flywheel
• Aluminum Timing cover
• Aluminum Finned Ford Racing Valve Covers
• New Fuel Lines and Gas Filter
• Polished Edelbrock Vic Jr. Single Plane
• Edelbrock 800 cfm 4 barrel w/ electric choke
• Elec Accel Billet Distributor & high voltage Coil
• High Flow Polished Aluminum Water & Fuel Pump
• Champion Spark plugs w/ 8mm ACCEL Spiral Wires
• New Chrome Thermostat Housing
• Oval aluminum finned air cleaner w/ Cobra logo
• Chrome 100 amp. Alternator and Polished Brackets
• March Pulley Setup with Serpentine-Belt
|
|
JCoop
Wed May 3, 2006 4:29pm
|
|
blueovalfanatic
Tue September 5, 2006 1:06pm
Rating: 10
|
Heads
CC'ing the heads just to get an idea of where I stand compression-wise. Heads are C6AE-R's. The block and heads will soon be going to the machine shop.
|
|
fastraxsg
Mon October 2, 2006 8:35am
|
Penang_Malaysia_1994
Last Castrol International MX in Malaysia, Dec. 1994. Finished 2nd in the Open Trail Class. Honda XR 250 with big bore kit, Ohlins front and rear, Al Baker frame and Al Baker flowed head. Sweet mud machine.
|
|
