Bernica
Sun March 1, 2009 10:54am
|
Fender / Body Skirt
From Finish Line. Fits like a glove
|
|
Danr55
Sun March 1, 2009 5:05pm
Rating: 10
|
Hooters Car Show..
First Place Trophy They like Cobras.
|
|
kitcarbp
Fri March 6, 2009 7:29am
Rating: 9
|
Ford_Raditor_Heat_Rejection_Chart- Street Rod Example
This chart compares the heat rejection rate (cooling capacity) of three different types of radiators tested on an old Ford Street Rod. Coolant flow rate is held constant at 7 gpm (typical flow at idle perhaps, not sure where its being measured ???). It graphs the heat rejection for each radiator versus air flow through the radiator core. It is comparing 3 diff rad designs/materials at different CFMs through the core. The more air flow you have for a given coolant flow rate (7 gpm in this example) , the higher the heat rejection, basically linear in this example. The author of this graph is most likely selling the high efficiency radiator showing the improvement over the other two designs. To sum it up, the radiator at the top of the chart appears to be the most efficient at a low coolant flow rate (7 gal/min) over all air flows tested. Ya see how important rad core/tank design is? I learned something here.
|
|
428street
Wed March 11, 2009 10:51am
|
|
Danr55
Sun March 22, 2009 3:16pm
Rating: 10
|
Over haul on Red One.
It's beginning to look like a motor again!
|
|
Danr55
Sun March 22, 2009 3:16pm
Rating: 10
|
Over haul on Red One.
It's beginning to look like a motor again!
|
|
Danr55
Sun March 22, 2009 3:16pm
Rating: 10
|
Over haul on Red One.
It's beginning to look like a motor again!
|
|
Danr55
Sun March 22, 2009 3:16pm
Rating: 10
|
Over haul on Red One.
It's beginning to look like a motor again!
|
|
Danr55
Sun March 22, 2009 3:16pm
Rating: 10
|
Over haul on Red One.
It's beginning to look like a motor again!
|
|
DocDirk
Wed April 8, 2009 7:27pm
|
Rear of lower link arm
This looks like it will bind if the axle moves up at all, will probably have to be rounded off. The arm has two welded bends in it so I doubt I can replace it accurately with a tube.
|
|
DocDirk
Wed April 8, 2009 7:27pm
|
Opposite side rear attachment of lower arm.
Doesn't look like it's going to allow much vertical movement either...given the square end of the link in a square receptacle...
|
|
HI Cobra
Mon April 13, 2009 9:19pm
Rating: 10
|
This is why I like to go to my second home in Texas!
|
|
DocDirk
Sat April 25, 2009 1:13pm
Rating: 10
|
Invisible grill
Grill painted black looks like the "Open front" look I like so much.
|
|
DAVID GAGNARD
Sat April 25, 2009 6:03pm
|
girdle
stud girdle damage, it held everything together like is was supposed to do.......
|
|
fkemmerer
Thu May 14, 2009 6:59am
|
AFR1
Sample AFR table for an EFI FE. NOTE THAT NO ONE SHOULD COPY THIS TABLE AND JUST USE IT - THESE SETTINGS ARE NOT APPROPRIATE FOR EVERY MOTOR AND WHAT WORKS FINE IN MINE MAY VERY LIKELY DAMAGE YOURS.
|
|
