LwCwb
Mon May 2, 2005 6:03pm
Rating: 10
|
R Code Comet
A real sleaper, chrome wheel covers, average paint job, standard interior, you wouldn't notice it was a "Different" Car until it passed you and you got a ear full of the R Code 427. Gene Latta Car Show.
|
|
Naumoff
Fri May 6, 2005 2:22am
Rating: 10
|
427 S/O on run stand at SA
|
|
Coupecrazy
Fri June 3, 2005 10:12pm
|
Blueprinted Tremec 6-speed by Rockland Standard Gear
|
|
lovehamr
Thu June 9, 2005 8:39pm
|
Super_Comet
Snapped this while standing in line for Bud.
|
|
RobV
Sun June 12, 2005 7:59pm
|
Off the trailer and waiting to go in the garage
The body and frame is off the trailer and awaits the jack stands in the garage.
|
|
Barry Nelson
Thu October 13, 2005 1:51pm
Rating: 10
|
scan0005
Allan Moffat trans am mstang press day sandown circuit 1969 Allan in the drivers seat I;m standing at the front door
|
|
Dirtrich
Tue February 21, 2006 7:43pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker 505hp build sheet...
• Blue printed machined 351W version Early Casting Block ('69) with Block Girdle Installed
• Scat Forged Steel 4.100 Stroke Crankshaft
• H Beam Rods 6.200" - ARP HD Rod Bolts
• Power Forged 10.5 to 1 Flat Top HP Pistons
• J & E Chrome Moly Ring Set
• Heavy Duty Double Roller Dynagear Timing Set
• Comp Cams Hydraulic Roller Retrofit Camshaft
• Clevite H series Racing Bearings
• Polished Edelbrock Victor Jr. cylinder heads
• Chrome Moly Hardened pushrods
• High Intensity Scorpion True Roller Rockers
• Melling HV Oil pump with Hardened FMS Drive Rod.
• Complete Fel-pro Gasket set
• Heavy Duty Harmonic Balancer
• New SFI Approved 10.5 inch Standard Flywheel
• Aluminum Timing cover
• Aluminum Finned Ford Racing Valve Covers
• New Fuel Lines and Gas Filter
• Polished Edelbrock Vic Jr. Single Plane
• Edelbrock 800 cfm 4 barrel w/ electric choke
• Elec Accel Billet Distributor & high voltage Coil
• High Flow Polished Aluminum Water & Fuel Pump
• Champion Spark plugs w/ 8mm ACCEL Spiral Wires
• New Chrome Thermostat Housing
• Oval aluminum finned air cleaner w/ Cobra logo
• Chrome 100 amp. Alternator and Polished Brackets
• March Pulley Setup with Serpentine-Belt
|
|
hogster
Tue May 9, 2006 3:52am
|
Unknown Aussie
This is my / will be my new car.
I don't know what it is, running XF and cortina suspension, standard ford 9' rear. Built like a brick thunderbox and looks sensational.
Anyone got one the same please let me know. Take some of the brainwork out of it, I have a headache????
|
|
nanard289
Fri May 19, 2006 1:25pm
|
my own header pipes
It is always difficult to build a complet header pipes. I have just modified a standard part (for Yates heads) to adapt it on the lateral side
|
|
blueovalfanatic
Tue September 5, 2006 1:06pm
Rating: 10
|
Heads
CC'ing the heads just to get an idea of where I stand compression-wise. Heads are C6AE-R's. The block and heads will soon be going to the machine shop.
|
|
aldersonjames20
Sun September 10, 2006 5:18am
Rating: 10
|
|
Clois Harlan
Tue October 31, 2006 2:53pm
Rating: 10
|
Hardtop Photos
I know these aren't the pictures you want but right now our weather is crap and I haven't got my new radiator in from my speed shop. If you want me to after I get my radiator installed sometime next week and I get my Cobra off jacks I can mount the hardtop and shot as many pictures as you like.
My roll bar stands 16" tall and 15" wide and measures from the back of the edge of my cockpit to the end of my diagonal roll bar support 16 1/4". Additionally, I have approx 1" clearance from the top of my roll bar to the headliner of my top when installed. Call me if you have any questions at 918-633-5336 if you like.
Clois
|
|
Clois Harlan
Tue October 31, 2006 2:53pm
Rating: 10
|
Hardtop Photos
I know these aren't the pictures you want but right now our weather is crap and I haven't got my new radiator in from my speed shop. If you want me to I will be glad to take some more pictures after I get my radiator installed sometime next week and I get my Cobra off jacks I can mount the hardtop and shot as many pictures as you like.
My roll bar stands 16" tall and 15" wide and measures from the back of the edge of my cockpit to the end of my diagonal roll bar support 16 1/4". Additionally, I have approx 1" clearance from the top of my roll bar to the headliner of my top when installed. Call me if you have any questions at 918-633-5336 if you like.
Clois
|
|
Clois Harlan
Tue October 31, 2006 2:53pm
Rating: 10
|
Hardtop Photos
I know these aren't the pictures you want but right now our weather is crap and I haven't got my new radiator in from my speed shop. If you want me to after I get my radiator installed sometime next week and I get my Cobra off jacks I can mount the hardtop and shot as many pictures as you like.
My roll bar stands 16" tall and 15" wide and measures from the back of the edge of my cockpit to the end of my diagonal roll bar support 16 1/4". Additionally, I have approx 1" clearance from the top of my roll bar to the headliner of my top when installed. Call me if you have any questions at 918-633-5336 if you like.
Clois
|
|
Clois Harlan
Tue October 31, 2006 2:53pm
Rating: 10
|
Hardtop Photos
I know these aren't the pictures you want but right now our weather is crap and I haven't got my new radiator in from my speed shop. If you want me to after I get my radiator installed sometime next week and I get my Cobra off jacks I can mount the hardtop and shot as many pictures as you like.
My roll bar stands 16" tall and 15" wide and measures from the back of the edge of my cockpit to the end of my diagonal roll bar support 16 1/4". Additionally, I have approx 1" clearance from the top of my roll bar to the headliner of my top when installed. Call me if you have any questions at 918-633-5336 if you like.
Clois
|
|
