 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
1 |
2 |
3 |
4 |
5 |
6 |
| 7 |
8 |
9 |
10 |
11 |
12 |
13 |
| 14 |
15 |
16 |
17 |
18 |
19 |
20 |
| 21 |
22 |
23 |
24 |
25 |
26 |
27 |
| 28 |
29 |
30 |
|
|
|
|
|
|
CC Advertisers
|
|
|
90 result(s) to your search. (short)
|
Prev Page ·
|
|
boatman
Tue February 19, 2002 6:14am
|
trailer for Cobra
will hold full size short bed p-u side door on right side
|
|
Naja
Sat August 17, 2002 11:44am
|
Naked 533 cid EFI
A look at Naja's powerplant with most of the 'accessories' off of it. Atop is a 1200 cfm Accel throttle body, then a Torker II manifold (a significant restriction for this engine), to the new Edelbrock 6066 aluminum heads, 65 lb. Siemens injectors (supplied by an Aeroequip pump). Custom grind roller CompCam with .662 i/e lift, solid lifters, roller rockers under the custom valve cover by Innovation West (only ones like them in the world). A medium stoker with .080 overbore gives 533 cid. Wiseco pistons have 18cc dish to give 9.8:1 compression ratio. I was surprised when the redline was set at 7k, but the 2 people doing the engine work said it would have no trouble handling it.
It dyno'd at 491 hp (5200 rpm) and 548 ft-lbs (4700 rpm) - remember the Torker II being a huge restriction. It was built with reliability (first) in mind, then for torque. The lowest rpm that they data logged during the dyno was 2600, and it was already doing 525 ft-lbs.
This powers a C6 tranny leading to a 9 inch, live rear end with a 2.73 running gear. Haven't run it on the road much, but have gotten over 15 mpg on two, short trips. Spark control completely MSD including 7AL-2, Pro Power HVC coil, billet distributor with Pro cap. All of this is managed by a SpeedPro ECU. It idles at about 950 rpm.
|
|
Mark Roe
Mon September 9, 2002 5:18pm
Rating: 10
|
|
Mark Roe
Mon September 9, 2002 5:19pm
Rating: 10
|
|
Mark Roe
Mon September 9, 2002 5:55pm
Rating: 10
|
|
Mark Roe
Wed September 11, 2002 4:55pm
Rating: 10
|
Short block on dyno
We're getting close!!
|
|
Charlie Conner
Tue November 19, 2002 9:41am
|
GT 40 Aluminum Heads
I have just worked the ports and runners over and shaved these y303 heads combustion chambers down to 55 cc's, those are Proform 1.7:1 pedestal mount rockers which fit under the short cast aluminum valve covers after you remove the baffles and machine the mounting bosses flush. Craig Blood of Blood Enterprises in Auburn Washington is my chief technical advisor, parts supplier and machinist for the shaving and valve cutting, i cannot recommend he and his crew highly enough! If you want the best quality and no BS he is your man.
|
|
zipzip
Wed June 11, 2003 7:11pm
|
|
zipzip
Wed June 11, 2003 7:21pm
|
|
Cobra Carlo
Thu July 10, 2003 8:44am
|
|
nikbj68
Fri August 22, 2003 3:33am
Rating: 5.5
|
39 PH in the `shop
Note the short bootlid for access when the Le Mans had top is fitted.
|
|
Bruce Edwards
Thu January 22, 2004 7:41pm
|
Rolling
Well looks like we got in the frame ok. Drive shaft looks like it will be a bit short. Talk about your tight fit! Less than 1/4 inch on both sides of the trans pan!
|
|
Rick Parker
Sun February 22, 2004 10:20pm
Rating: 10
|
Snakes
Fabricated headers to increase primary tube length rather than use OEM Short FIA block hugger type. A "LOT" of work.
|
|
MAXVELO
Tue February 24, 2004 6:31am
|
DEFAULT VIEW (EVERYONES VIEW)
WHAT ANYONE WHO HAS ANY GUT TO CHALLENGE ME SEES SHORTLY AFTER!
|
|
simon clemens
Tue June 22, 2004 6:29am
|
|
|
All times are GMT -7. The time now is 08:35 PM.
Links monetized by VigLink |
