DocDirk
Wed April 8, 2009 7:27pm
|
Sidepipe Stainless Cover
Made by Stainless Specialties
|
|
cay5628
Sat May 2, 2009 10:15am
Rating: 10
|
Engine
Engine picked up from Smeding Performance.
351W Dart block, bored and stroked to 427, all forged internals. AFR aluminum heads, with DynaTek classic fule injection. It made 560 hp and 580 lbft torque. It'll scooy
|
|
392cobra
Tue May 19, 2009 5:51am
|
|
PHM
Fri June 19, 2009 6:24am
|
Mike's Cobra
Custom Billet Radiator Cap I made and Custom Oil breather
|
|
Pete Munroe
Wed July 22, 2009 9:58pm
Rating: 6
|
Canton oil thermostat
ERA 289 FIA with Canton oil thermostat. This is the drivers side hose run to the cooler.
Off-set the Canton thermostat cooler line outlets by taking it apart and rotating the segments. The segments can "clocked" in 90 degree increments, so the oil cooler hoses can exit on opposing sides. Made plumbing a lot easier in this installation. Fewer angles in the swivel fittings helps avoid any restriction on oil pressure.
|
|
kitcarbp
Mon September 21, 2009 7:20am
Rating: 10
|
West Coast Griffin Rad Brackets
Here is a shot of my custom rad brackets made from 1/8 x 1.5" aluminum strip. Its a two peice design without welds and is adjustable to the core thickness. This core is 2.75" wide. I used High density EPDM sponge foam to line the inside of the bracket to absord vibration and protect the core frame.
|
|
martrogers
Fri October 2, 2009 11:59pm
|
ackit
Pic showing the drilling template with 2 holes drilled. In the background is a template I made by putting cling film on the bonnet, and getting the curve into body filler. This mould template was then used to ensure the AC would fit the curve of the bonnet.
|
|
martrogers
Fri October 2, 2009 11:59pm
|
auto
Mould template particularly important for the Automatic logo. I made a pin template and curved the logo against a mould taken from the body - see bonnet pic.
|
|
fkemmerer
Thu October 8, 2009 10:31pm
|
Oil Thermostat - Final assembly before installation in the car.
This shows the Canton Oil Thermostat installed in a custom made bracket prior to installation in the car.
|
|
Z-linkCobra
Mon October 19, 2009 1:58pm
|
Build pics
Had this handle made to replace the t style handle that it came with originaly.Still not sure what to about the reverse handle though.
|
|
jbcobra67
Thu October 29, 2009 11:29am
Rating: 10
|
DSCF2256
Made the connection
|
|
cay5628
Sat November 14, 2009 10:27am
Rating: 10
|
Dynatek Injection
I'm using Dynatek Classic Fuel Injection (Now Dynaforce). Engine made 560 hp at 5400, 580 ft lb at 4700. Had 480 ft lb in at 2500 rpm. Lots of low end power.
|
|
tjl
Sun November 15, 2009 10:29am
Rating: 10
|
At Eriks museum
We had a meeting last fall, freind made this nice picture
|
|
kitcarbp
Sat November 28, 2009 6:09pm
Rating: 10
|
Mcleod steel flywheel for 460
This also shows my home made engine plate I made with a jig saw and a nice set of files. Trick was to use the old rusted one as my template and the starter bolt holes and register bore was my datum point to ensure correct starter alignment.
|
|
*13*
Sun November 29, 2009 3:49pm
Rating: 10
|
Weber Filters (Home Made)
Just a first try. SS mesh & Neoprene caps from McMaster Carr. Just wanted to see if it would work. Now that I know they do, I can clean them up a bit. Blurry picture is hiding the dirty engine compartment.
|
|
