zipzip
Wed October 26, 2005 10:06am
Rating: 10
|
ford 9 inch exploded view
|
|
Robert Sobers
Wed November 9, 2005 10:31am
|
Shelby R Model Clone
My 66 Shelby R Clone Specs.
D.S.S. Pro Bullet 306/308 Short Block Level 10 CNC
Rods: Forgings, shot-peened, Magna Fluxed, CNC Diamond resized and fitted with ARP Wave Loc rod bolts. Balanced to racing tolerances.
Crank: Production crankshaft, thermal cleaned, shot-peened, Magna Fluxed, precision ground, oil scooped and chamfered and balanced to racing tolerances.
Pistons: DSS PRO-LITE Forged 2 valve relief flat top, CNC fly-cut for most aftermarket race cams and heads. Balanced to racing tolerances.
Rings: Sealed Power/ Speed-Pro Moly rings.
Bearings: Tri-metal rod and main bearings.
Block: 5.0 roller cam block, thermal cleaned, stress relieved, Magna Fluxed, threads chased, mains checked and corrected, oil galleys tapped for thread in plugs and the decks are CBN squared and equalized.
Transmission- C4 Automatic
Rear End- 8 Inch Detroit Locker 355 Gears.
Gt40Y Heads ported and polished.
Comp Cam by Bennett Racing Cams.
Edelbrock Air Gap Manifold
670 Holley Street Avenger Carb.
1.6 Roller Rockers
MSD Distributor
MDS 6AL Ignition Control Unit
Edelbrock Fuel Pump
Edelbrock Water Pump
AFCO Aluminum Radiator
Canton 7 QT. Oil Pan
Windage Tray
Shelby R Valve Covers with Vent Stacks
Holley Electric Fuel Pump
3/8 Stainless Fuel Line Tank to Pump
Spal Electric Fan
3 ¾ Auto-Meter Tach
Raptor LED Shift Light
Hurst Quarter Shifter with Line-Lock
K&N X-Stream Air Cleaner
Trunk Mounted Battery with Cut Off Switch
PA Performance 3-G Alt.
PA Performance Mini-Starter
Total Control Products Strut Tower Brace System
Total Control Products Sub-Frame Connectors
Auto-Power Roll Bar
Simpson Safety Harness
Hunsaker Racing Seats
Mac Headers
Mac Exhaust System with 2 ½ Inch Dumps.
R-Model Gauge Panel with 2 5/8 Autometer Gauges.
Cobra Country Oil Breather System.
|
|
Jim Norris
Sun November 20, 2005 7:03pm
Rating: 10
|
|
greg schroeder
Mon January 23, 2006 2:43pm
Rating: 10
|
M/T ET Street Radial
Mounted on 4 inch backspace 15 inch wheel on SPF 2040
|
|
greg schroeder
Mon February 6, 2006 7:40am
|
Roush 427R-095
Roush 427R engine with 2 inch primary headers and 870 Holley Avenger carb
|
|
Dirtrich
Tue February 21, 2006 7:43pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker 505hp build sheet...
• Blue printed machined 351W version Early Casting Block ('69) with Block Girdle Installed
• Scat Forged Steel 4.100 Stroke Crankshaft
• H Beam Rods 6.200" - ARP HD Rod Bolts
• Power Forged 10.5 to 1 Flat Top HP Pistons
• J & E Chrome Moly Ring Set
• Heavy Duty Double Roller Dynagear Timing Set
• Comp Cams Hydraulic Roller Retrofit Camshaft
• Clevite H series Racing Bearings
• Polished Edelbrock Victor Jr. cylinder heads
• Chrome Moly Hardened pushrods
• High Intensity Scorpion True Roller Rockers
• Melling HV Oil pump with Hardened FMS Drive Rod.
• Complete Fel-pro Gasket set
• Heavy Duty Harmonic Balancer
• New SFI Approved 10.5 inch Standard Flywheel
• Aluminum Timing cover
• Aluminum Finned Ford Racing Valve Covers
• New Fuel Lines and Gas Filter
• Polished Edelbrock Vic Jr. Single Plane
• Edelbrock 800 cfm 4 barrel w/ electric choke
• Elec Accel Billet Distributor & high voltage Coil
• High Flow Polished Aluminum Water & Fuel Pump
• Champion Spark plugs w/ 8mm ACCEL Spiral Wires
• New Chrome Thermostat Housing
• Oval aluminum finned air cleaner w/ Cobra logo
• Chrome 100 amp. Alternator and Polished Brackets
• March Pulley Setup with Serpentine-Belt
|
|
mj_duell
Fri February 24, 2006 9:57am
|
1.25 inch / Front Sway Bar (option)
1.25 inch / Front Sway Bar (option)
|
|
mj_duell
Fri February 24, 2006 9:58am
|
1.0 inch / Rear Sway Bar (option)
1.0 inch / Rear Sway Bar (option)
|
|
greg schroeder
Tue February 28, 2006 8:19am
Rating: 10
|
325_50_15_MT_ET_Street_Radial_rear1
325/15 50 Mickey Thompson ET street radials on 4 inch backspace, 9.5 inch wide wheel
|
|
Full Throttle Al
Thu May 11, 2006 6:36am
Rating: 10
|
CSX4083
Footboxes had to be notched about 6 inches on each side to fit the cammer heads.
|
|
hogster
Sat June 10, 2006 3:22am
|
Front coils - TCI Chrome Shocks
Finally the front coils have arrived, look very nice.
!2 inch ride height, 300lb springs.
|
|
greg schroeder
Wed November 15, 2006 8:57am
Rating: 10
|
17 inch wheels
Wheels from Vintage Wheels
Tires from Yokohama
|
|
Anthony
Wed November 15, 2006 5:57pm
Rating: 10
|
427 SO Hi-Riser engine
427 SO, aluminum HiRiser heads, 780 Holley Lemans carb, 10.5:1 CR, bored 0.017" over, displacement 429 cubic inches. Engine built to replicate a lightweight competition engine.
Chassis dyno tuned - Got 454 rwhp @ 5900 rpm's and still climbing, and 488 rwtq @ 3900 rpm's.
|
|
Anthony
Wed November 15, 2006 6:00pm
Rating: 10
|
427 Hi-Riser engine
427 SO, aluminum HiRiser heads, 780 Holley Lemans carb, 10.5:1 CR, bored 0.017" over, displacement 429 cubic inches. Engine built to replicate a lightweight competition engine.
Chassis dyno tuned - Got 454 rwhp @ 5900 rpm's and still climbing, and 488 rwtq @ 3900 rpm's.
|
|
greg schroeder
Sun December 3, 2006 8:02am
Rating: 10
|
2100DA
DA 2100 ft.
10.913 @ 128.759
stuff on my car for the off idle pass
Superformance 2040
Roush 427R-095
Olthoff 2" primary headers
Buckshot Racefab side pipes, 3 inch internal
Pro-Systems 1000ish CFM carb
1/2" and 8AN fuel line from tank pick up to carb
Aeromotive fuel filter
Carter mechanical self regulating fuel pump
maid in Taiwan oval Cobra type intake with 2 1/2" inch tall filter
Mickey Thompson ET Street Drag radials, 325/50 15
Detroit Truetrac 3.73 rear end
TKO 600
|
|
