boxhead
Mon October 10, 2005 5:48am
Rating: 10
|
Master cylinders in place
Here are all the master cylinders bolted up
|
|
jerry w
Sun October 30, 2005 5:21pm
Rating: 10
|
cobra_boostermastercylinder
|
|
66rdster
Sun November 6, 2005 7:30pm
|
Trim Piece for Master Cylinders
Covers the spacer nuts used to level the master cylinders.
|
|
66rdster
Sun November 6, 2005 7:34pm
Rating: 10
|
Master Cylinders Installed
|
|
LMH
Fri November 11, 2005 1:57pm
Rating: 9.66667
|
Master_Cylinders
Brake/Clutch Master Cylinders, Plate and Steering Shaft.
|
|
Tongue Pirate
Sun December 18, 2005 7:49pm
|
ERA Slave cylinder & mount
Since my block was a 1964 with the 5 bolt bellhousing things didn't line up with the clutch arm. This is before I refabed the mount to fit
|
|
mickmate
Thu February 9, 2006 7:05am
Rating: 10
|
Masters
Master cylinders mounted and plumbed.
|
|
Dirtrich
Tue February 21, 2006 7:43pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker 505hp build sheet...
• Blue printed machined 351W version Early Casting Block ('69) with Block Girdle Installed
• Scat Forged Steel 4.100 Stroke Crankshaft
• H Beam Rods 6.200" - ARP HD Rod Bolts
• Power Forged 10.5 to 1 Flat Top HP Pistons
• J & E Chrome Moly Ring Set
• Heavy Duty Double Roller Dynagear Timing Set
• Comp Cams Hydraulic Roller Retrofit Camshaft
• Clevite H series Racing Bearings
• Polished Edelbrock Victor Jr. cylinder heads
• Chrome Moly Hardened pushrods
• High Intensity Scorpion True Roller Rockers
• Melling HV Oil pump with Hardened FMS Drive Rod.
• Complete Fel-pro Gasket set
• Heavy Duty Harmonic Balancer
• New SFI Approved 10.5 inch Standard Flywheel
• Aluminum Timing cover
• Aluminum Finned Ford Racing Valve Covers
• New Fuel Lines and Gas Filter
• Polished Edelbrock Vic Jr. Single Plane
• Edelbrock 800 cfm 4 barrel w/ electric choke
• Elec Accel Billet Distributor & high voltage Coil
• High Flow Polished Aluminum Water & Fuel Pump
• Champion Spark plugs w/ 8mm ACCEL Spiral Wires
• New Chrome Thermostat Housing
• Oval aluminum finned air cleaner w/ Cobra logo
• Chrome 100 amp. Alternator and Polished Brackets
• March Pulley Setup with Serpentine-Belt
|
|
Slither
Mon April 17, 2006 8:13pm
Rating: 10
|
|
nanard289
Sat May 6, 2006 1:39pm
Rating: 10
|
Special intake manifold
After several weeks of work my special inlet manifold is ready. I hope to be able to test it next month (exhaust pipes are not yet welded). It is not easy to adapt properly a set of Weber 48IDF on Yates head cylinders but I am confident about the result.
|
|
Blittleton
Wed May 17, 2006 5:45pm
Rating: 10
|
Backdraft and new slave cylinder
|
|
HSSS427
Tue May 30, 2006 12:10pm
|
Cylinders 5-8 post water leak
|
|
Snakester
Sun June 25, 2006 1:00pm
Rating: 10
|
Snakester's Cobra Accessories
Heat Shield for Master Cylinders
|
|
Toby
Tue July 11, 2006 7:11am
Rating: 10
|
cobra44
new triple master cylinders and mount bracket
|
|
nanard289
Mon July 24, 2006 4:34am
Rating: 9.8
|
Weber_manifold_modification
Big job to adapt a weber manifold on Yates head cylinders. I start from a 351 Cleveland manifold (from de Tomaso Panthera) and a J Roush manifold for Holley carb to finish on a 302 Windsor with the top of the first and the bottom of the second
|
|
