 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
1 |
2 |
3 |
| 4 |
5 |
6 |
7 |
8 |
9 |
10 |
| 11 |
12 |
13 |
14 |
15 |
16 |
17 |
| 18 |
19 |
20 |
21 |
22 |
23 |
24 |
| 25 |
26 |
27 |
28 |
29 |
30 |
31 |
|
|
CC Advertisers
|
|
Anthony
Tue November 14, 2006 9:54pm
Rating: 10
|
cobra_0014
427 SO, Aluminum Hi-Riser Heads, original single 4bbl intake with original Holley 780 Vac Sec carb with LeMans bowls
|
|
Anthony
Tue November 14, 2006 9:57pm
Rating: 10
|
cobra_0023
427 SO, Aluminum Hi-Riser Heads, original single 4bbl intake with original Holley 780 Vac Sec carb with LeMans bowls
|
|
greg schroeder
Tue November 21, 2006 3:09pm
|
air filter
S and B tall oval air filter in maid in Taiwan Cobra type intake
|
|
greg schroeder
Sun December 3, 2006 8:02am
Rating: 10
|
2100DA
DA 2100 ft.
10.913 @ 128.759
stuff on my car for the off idle pass
Superformance 2040
Roush 427R-095
Olthoff 2" primary headers
Buckshot Racefab side pipes, 3 inch internal
Pro-Systems 1000ish CFM carb
1/2" and 8AN fuel line from tank pick up to carb
Aeromotive fuel filter
Carter mechanical self regulating fuel pump
maid in Taiwan oval Cobra type intake with 2 1/2" inch tall filter
Mickey Thompson ET Street Drag radials, 325/50 15
Detroit Truetrac 3.73 rear end
TKO 600
|
|
hi-tech cobra
Sat December 23, 2006 1:35pm
Rating: 10
|
DSC_0049
Ported GT-40x heads, intake side
|
|
slow 427
Sat December 30, 2006 4:08pm
|
cold air intake scoops
fibreglass cold air intakes ducted from the front brake vents
|
|
slow 427
Sat December 30, 2006 4:08pm
|
both air intakes
progress so fro after 7 months
|
|
speed220mph
Fri February 9, 2007 12:17pm
Rating: 10
|
Crack in Tunnel Port Head
Crack between intake-valve seat and sparkplug hole was repaired by pinning, replacing plug threads with Heli-Coil and installing new valve seat.
|
|
greg schroeder
Mon February 19, 2007 5:30pm
|
dynojet 475.3 wheel HP
Roush 427R-095 single plane intake manifold
Pro-Systems 1000 cfm carb
oval 2.25 in. high air cleaner
2" primary headers
Buckshot Racefab side pipes
|
|
buildride
Thu March 1, 2007 11:55pm
|
1967 427 S.C. Cobra Viper Blue
1967 427 S.C. Cobra Viper Blue.Smeding 427 Cobra Special. Bored and stroked to 427 cu.in., 450hp 450ft lbs est., 10.2:1 comp. 351 SVO Sportsman II block 4.030” bore, 4340 forged crank 4.170” stroke, forged pistons floating pin, 4340 steel H beam rods 7/16 ARP bolts, engine balanced to ½ gram, roller cam .493/.510 lift 279/289 dur, Edelbrock Performer RPM aluminum heads 2.02/1.60 SS valves springs single w/damper, dual roller timing chain, aluminum roller rockers 1.6 ratio, Intake Edelbrock aluminum performer, Holley 600 four barrel, HEI dist, March serpentine billet aluminum pulley set.
|
|
blueovalfanatic
Fri March 16, 2007 9:24am
Rating: 10
|
Intake
Almost done polishing the Performer RPM
|
|
cwmcobra
Fri March 23, 2007 6:24am
Rating: 10
|
Leaky Intake Gasket
Fel-Pro being replaced with Victor Reinz
|
|
Anthony
Wed April 4, 2007 7:54pm
Rating: 10
|
Chassis Dyno - Initial Run 427 High Riser
Self built 427 SO, stock stroke, 429 ci., Dove aluminum High Rsier heads, mildly ported, 10.5 : 1 CR, original holley 780 cfm LeMans carb, vacuum secondary, on an original single four BBL Hi-Riser intake. Chassis Dyno is at Performance Engineering, Hamilton, OH.
Initial run with engine as built by me, with jetting as supplied with carburetor.
|
|
Anthony
Wed April 4, 2007 7:55pm
Rating: 10
|
Chassis Dyno - Last Run 427 High Riser
Self built 427 SO, stock stroke, 429 ci., Dove aluminum High Riser heads, mildly ported, 10.5 : 1 CR, original holley 780 cfm LeMans carb, vacuum secondary, on an original single four BBL , dual plane, Hi-Riser intake. Chassis Dyno is at Performance Engineering, Hamilton, OH.
Carb jets changed, and timing adjusted by Performance Engineering. Picked up 80 ft-lbs torque and 60 hp by chassis dyno tuning.
With a 20% loss, estimated max flywheel torque is about 600, with about 570 flywheel HP at 5900 rpm's and still climbing.
The torque curve is pretty flat.
|
|
Anthony
Wed April 4, 2007 7:57pm
|
Chassis Dyno - Last Run 427 Hi-Riser Air-Fuel Ratio
Self built 427 SO, stock stroke, 429 ci., Dove aluminum High Riser heads, mildly ported, 10.5 : 1 CR, original holley 780 cfm LeMans carb, vacuum secondary, on an original single four BBL , dual plane, Hi-Riser intake. Chassis Dyno is at Performance Engineering, Hamilton, OH.
Carb jets changed, and timing adjusted by Performance Engineering. Picked up 80 ft-lbs torque and 60 hp by chassis dyno tuning.
With a 20% loss, estimated max flywheel torque is about 600, with about 570 flywheel HP at 5900 rpm's and still climbing.
|
|
|
All times are GMT -7. The time now is 06:28 AM.
Links monetized by VigLink |
