DC COBRA
Tue February 10, 2004 4:41pm
Rating: 10
|
|
Lynmac
Tue March 16, 2004 4:54am
|
|
BULLITT
Mon March 22, 2004 11:55pm
Rating: 10
|
How I Got MY COBRA
Looks Pretty Bad?
I was Broadsided by a Rig that was Speeding in excess of 75 MPH,Weaving in & out of traffic.
My seatbelt broke & I was thrown from my Rig as the Cab was Torn Off, partly due to falty Spot welds at the Factory in Brazil (95% were COLD I just had 5% of the Total Spot welds holding my Cab on to the Frame)
I was Comatose for 6.5 Weeks, I had ALL my Ribs Crushed, 4 holes in each Lung, Both Collar bones broken in 3 places, 2 Skull Fractures, 1 concaved fracture in the rear of my Skull, I lost 7 Cm of Brain Tissue on the Left Frontal Lobe, I Lost 7 Pints of Blood, I had 3 Heart Beats per Minute when they got me to the Hospital.
My saving Grace, was a Doctor who was doing a "Ride a long" Who Cut My lungs open & Blead them while I was laying on the 101 Freeway & "Bagged" Me all the way to the Hospital.
But Worst of all, I was hit by an "Illegal Immagrant" who changed his story 8 times & CHP let him go with not as much as a Warning. Can you believe that B.S ?
|
|
simon clemens
Mon July 5, 2004 3:13am
|
Quad flanges
118mmX138mm, 8mm thick, 1-5/8" exhaust holes
UHP water cut.
|
|
boxhead
Sat July 10, 2004 6:02am
Rating: 10
|
engine_mount_out_of_alignment
Here you can see what I ment when I said the mount didnt line up, the r/h mount is sitting in locateing hole
|
|
bentl11
Wed July 14, 2004 6:41pm
|
|
Anthony
Sat August 7, 2004 11:28am
Rating: 10
|
factory 427 High Riser intake
factory 427 HR single 4 bbl intake , I believe to be used on 427 comp cobra's. The intake originally was cast with a "4 hole" style carb pad, but someone modified it like a modern intake, with two large openings.
|
|
cobrajeff
Sun November 21, 2004 12:08pm
Rating: 10
|
351C Weber intakes
High-Port manifold on right. Note vacuum holes on inboard side, as opposed to th eold intake, where they were outboard.
Two bosses on intake for "hard" linkage, as opposed to th e"cable" linkage of the Pantera system.
|
|
Michael C Henry
Tue December 14, 2004 12:13pm
Rating: 10
|
padded dash
Fresh vinyl covered EM steel dash w/glove box I installed the glovebox.I didn't open up the holes for the large gauges enough.I have to lube the tach and speedo to remove or install. dash mounted Flaming River master switch not installed yet.
|
|
Michael C Henry
Wed December 15, 2004 10:08pm
Rating: 10
|
modified primary metering block
This is the main body side of the primary metering block.Notice the holes that is part of the modification
|
|
happyhouse
Fri January 21, 2005 1:15am
|
|
happyhouse
Fri January 21, 2005 1:16am
|
|
Morris
Tue March 1, 2005 7:31pm
|
|
cobrajeff
Wed March 23, 2005 9:26am
Rating: 10
|
Plastic Valve Covers
Here are two sets of plastic COBRA valve covers I made in the 70's. Thought the clear ones would really be cool. To really get the detail, I would have had to drill small air holes in them to get the vacuum machine to work well - I wasn't willing to do that.
|
|
simon clemens
Wed April 27, 2005 7:24am
|
Brake relocation
Rear brake relocation was needed to allow clearance between the coilovers and the calipers. Re-drilled calliper mount bracket holes so the caliper sits about 40 degrees foward from original position. Also had to swap Left & Right brake assemblys to opposite sides, so the hand brake cable now will run on top of the axle & still be accuated by a foward movement. I wonder if others have thought of this solution?
|
|
