 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
1 |
2 |
3 |
4 |
5 |
6 |
| 7 |
8 |
9 |
10 |
11 |
12 |
13 |
| 14 |
15 |
16 |
17 |
18 |
19 |
20 |
| 21 |
22 |
23 |
24 |
25 |
26 |
27 |
| 28 |
29 |
30 |
|
|
|
|
|
|
CC Advertisers
|
|
750hp
Sun March 21, 2004 1:58am
Rating: 10
|
|
tom meyers
Sun May 2, 2004 7:42am
|
THE STALLION
6'' LONGER AND 4'' WIDER
SIZE DOES MATTER
|
|
Bruce Edwards
Thu May 6, 2004 3:53pm
Rating: 10
|
Bill's 351W front 2
Another picture of Bill's 351W (TampaFla) for his 289 ERA.
Somethings you do not see but that I will post when I get more time.
Forged Keith Black pistons .30, Double row timing set, .10/.10 crank, Hand fit Sealed Power 1/16 moly rings, trimetal Clevite 77 bearings, HP/HV Melling pump with a HD drive, Edelbrock Performer RPM cam, Roller tip rockers, Brass freeze plugs, Windage tray, Oil pan baffle welded into bottom of pan, Oil temp bung brazed to side of pan, High Rev anti pump up lifters, ARP Studs for mains,ARP rod bolts, modified oil pick up, treaded front oil galley plugs, matched block oil passage to oil pump and FelPro gaskets
|
|
392cobra
Tue May 18, 2004 3:49pm
Rating: 10
|
April '04 Dallas Meeting
Mine (l) & Matt's (r)
|
|
DAVID GAGNARD
Sat May 22, 2004 4:38pm
|
|
jwoodard
Mon June 14, 2004 10:56am
Rating: 10
|
Tulsa_Mid-Am_018
Lee Abramson, David Tittle, Mark Wheatley, "Bob" and Matt Tice
|
|
Bboriginal
Wed June 16, 2004 2:13pm
|
Detail of engine paint
Engine was painted and pearled to match the body
|
|
boxhead
Sat July 24, 2004 2:49am
Rating: 10
|
Wrong control arms
No matter what I tried there is no way the spring is going to fit without fouling the upper control arm.
|
|
Anthony
Sat August 7, 2004 12:19pm
Rating: 10
|
48mm IDA weber vs 58mm weber intakes
On the top is a new blue thunder 48mm IDA intake, with a 10 degree canted mount angle.
Below is a 1960's Hilborn Fuel injection system for a ford 427 with High Riser heads. The system consisted of two pieces, two banks of 4 throttle bores, of 2 7/16" (62mm) diameter, that are bolted to the top of the intake. I believe the intake has the 58mm weber bolt pattern and spacing. As you can see, the throttle bores are straight up, not canted at all. A somewhat rare intake. It has been polished, and no identification marks are visable. This should make alot of top end power. I unbolted one of the fuel injection throttle body castings to expose the mating surface of the intake.
As you compare the two intakes, you can see the larger bolt pattern of the 58mm weber intake, as well as the larger ports. There isn't enough of material on a 48IDA intake to redrill for a 58mm pattern.
|
|
Anthony
Sat August 7, 2004 12:22pm
Rating: 10
|
48mm IDA intake vs Hilborn fuel injection on 58mm weber intake
On the left is a new blue thunder 48mm IDA intake, with a 10 degree canted mount angle.
On the right is a 1960's Hilborn Fuel injection system for a ford 427 with High Riser heads. The system consisted of two pieces, two banks of 4 throttle bores, of 2 7/16" (62mm) diameter, that are bolted to the top of the intake. I believe the intake has the 58mm weber bolt pattern and spacing. As you can see, the throttle bores are straight up, not canted at all. A somewhat rare intake. It has been polished, and no identification marks are visable. This should make alot of top end power. I unbolted one of the fuel injection throttle body castings to expose the mating surface of the intake.
As you compare the two intakes, you can see the larger bolt pattern of the 58mm weber intake, as well as the larger ports. There isn't enough of material on a 48IDA intake to redrill for a 58mm pattern.
|
|
Rick Parker
Thu August 26, 2004 8:03pm
Rating: 10
|
Body insulation material
This blue canvas belting was purchased at a surplus outlet pretty inexpensive too.
|
|
sp1410
Sun August 29, 2004 12:47am
Rating: 10
|
Cobra's garage mate
1970 Olds 442 W-30 4spd car. #'s matching original.
|
|
kitcarbp
Tue August 31, 2004 6:30pm
Rating: 10
|
460 Manual Cast Iron Ford Bell Housing (aka 351M/400M Bronco)
351M/400M bell housing- This was actually the first part purchased for my project, wow, what a long strange trip its been ! This required the use of a short-input shaft TKO 600 kit. I used a needle bearing type crankshaft pilot bearing.
Re-cond bell housing waiting for her mate for life
uses a top-loader bolt pattern and only 6.25 inches deep great for STREET duty Cobras. Total investment was $210 after heli-coil repair
|
|
newBDR
Fri September 3, 2004 7:04am
|
front wheel
wheel center color matches stripes
|
|
cobrajeff
Fri October 15, 2004 5:33am
Rating: 10
|
Collapsible Spare
I had a Campagnolo magnesium wheel narrowed to fit an inflatible collapsible spare tire. Polished it to match the road wheels.
|
|
|
All times are GMT -7. The time now is 08:12 AM.
Links monetized by VigLink |
