sganz
Tue December 23, 2008 9:11am
|
Cobra in Herb/Matt Adams VSE Monterey
Some shots of the chassis in Monerey
|
|
sganz
Tue December 23, 2008 9:11am
|
Cobra in Herb/Matt Adams VSE Monterey
Some shots of the chassis in Monerey
|
|
sganz
Tue December 23, 2008 9:11am
|
Cobra in Herb/Matt Adams VSE Monterey
Some shots of the chassis in Monerey
|
|
RJCCOBRA
Tue December 30, 2008 2:41pm
|
Shell Valley build
Here's the front of the car after we removed the radiator. There was a problem with some work that the radiator shop did and the driver's side tank leaked like a sieve. The good news is that the engine fired and we were able to time it.
|
|
RJCCOBRA
Tue December 30, 2008 2:41pm
|
Shell Valley build
Here's a picture of the under carriage. Hopefully we're pretty much finished with everything under the car.
|
|
RJCCOBRA
Tue December 30, 2008 2:41pm
|
Shell Valley build
Here's a shot of the sleeve that Buddy machined up to cover the joint between the steering column and shaft going to the rack and pinion.
|
|
RJCCOBRA
Tue December 30, 2008 2:41pm
|
Shell Valley build
Here's another shot of the sleeve. Looks great!
|
|
n6opv
Thu January 22, 2009 11:23pm
|
Arntz tranny tunnel
Shown here is the removable section of the tranny tunnel. With the big engine setback in all the Arntz / Butler cars, you can remove the transmission while seated if you desire. Only a few very late Butlers had this and all Arntz Type 4 cars. I have no idea what the many cutouts are for  Also shown are the two triangulation tubes that connect the center of the cowl hoop to the 2 main frame rails for increased rigidity. The 3rd leg of the roll bar (not shown) also attaches to the same point on the passenger side frame rail. This is Arntz Type 4 only as well.
|
|
RJCCOBRA
Fri January 23, 2009 2:43pm
|
Shell Valley build
Here's one more look at the license plate bracket.
|
|
RJCCOBRA
Fri January 23, 2009 2:43pm
|
Shell Valley build
Here's the hood after we straightened it and put the first layer of glass cloth on the inner panel.
|
|
RJCCOBRA
Thu January 29, 2009 3:22pm
Rating: 1
|
Shell Valley build
Here's the driver's side door latch assembly installed.
|
|
RJCCOBRA
Wed February 4, 2009 3:01pm
|
Shell Valley build
Here's another shot of the trunk lid with the mounting point for the license plate light raised by 1 inch.
|
|
taylor-played
Sat February 14, 2009 10:36pm
|
Inaugural Cruise
01-25-09 was a wonderful day 25+ miles put on her in about 2 hours giving local rides to everybody who helped along the way... Thanx for the help all of you...
|
|
kitcarbp
Mon February 23, 2009 5:59am
Rating: 10
|
Team Three Wheel for my West Coast- Custom sizes
Here is an image of the Team III wheel I am using on my West Coast Cobra, rear wheel is 12 inches wide and barely fits my 15 inch 325 BFG Drag Radials
|
|
kitcarbp
Mon February 23, 2009 6:09am
Rating: 10
|
Front Driver Corner View
Here is the status as of Feb 2009, nearing test fire stage.
|
|
