caccobra
Fri February 25, 2005 6:03am
Rating: 10
|
My 427 S/C Contemporary Cobra
428, close-ratio toploader, Smith's Guages, true pin-drive knock-offs, 3:54 Jag posi rear & suspension, 560 lift Comp. Cam's cam, roller rockers, springs, medium riser, Barry Grant 750 Gold Claw, turkey pan and correct aircleaner, full aluminum engine compartment & trunk, Connelly leather & Wilton wool interior, correct Guardsman Blue and Wimbledon White lacquer paint.
|
|
luke-44
Sun February 27, 2005 7:44pm
|
|
Morris
Tue March 1, 2005 7:25pm
|
BBS
18' X 9" front
18" X 11" Rear
6 Pin hub
|
|
Morris
Tue March 1, 2005 7:27pm
|
|
Morris
Tue March 1, 2005 7:31pm
|
|
pneall
Tue March 1, 2005 9:23pm
Rating: 10
|
|
JohnB
Thu March 3, 2005 10:59pm
|
Pinch me
At my house in San Jose, I really did it.
|
|
simon clemens
Sun April 3, 2005 7:53am
|
Hood Pull
Bonnet pin & catch mounts are fibre glassed into place. Will have a cable linked under the dash board for the hood pull. Gass struts will be added later to automatically lift the hood.
|
|
RallySnake
Tue April 5, 2005 12:10pm
Rating: 10
|
|
simon clemens
Mon April 18, 2005 4:52am
|
Adjustable Trailing Arms
Adjustable Commodore Top Trailing Arms have been used to set correct pinion angle.
|
|
jeffw
Mon April 18, 2005 6:35pm
Rating: 10
|
Cause of Broken Flywheel
Ford 176T Flywheel Ford Mini Starter Lakewood Bellhousing = DISASTER. Lakewood bellhousing will not work with offset starter pinions. Check the alignment in the blowup photo.
|
|
bshap
Thu April 21, 2005 4:03am
Rating: 8
|
Estate sale
Here is a beautiful NEARLY NEW 1983 Cobra. Properly and carefully built from a WEST COAST COBRA kit, it is fitted with a Ford 460ci V8 engine. This beast has only gone approximately 8000 miles since completion. Always stored inside. The builder/collector/owner recently passed away and this is an estate sale. It has a Nascar Can-Am chassis with power rack and pinion steering; 11-inch vented rotors with 4-piston racing calipers; 4-bar rear axle with 9-inch drop-out center section; 25 gallon race-legal fuel cell; weight 2970lbs (50/50 front/rear). Available with or without a spare fully-rebuilt 460ci engine. Located near Toronto Canada. Pre-purchase inspections and/or appraisals are welcome. Hard to find a nicer example! Asking cdn$56,000.00 (us$45,000) OBO Contact Bob Shapton 519-927-3966
|
|
simon clemens
Wed April 27, 2005 7:00am
|
3 Position Height Bracket
3 Position suspension height bracket on lower coilover eyelet.
12 Position dampen rate on 'QA1' shock. Plus adjustable spring tension.
Shortened BW Diff.
New 28 spline axles.
New 3.73:1 gear set.
New 4 pinion LSD assembly.
|
|
simon clemens
Wed April 27, 2005 7:00am
|
4 Link & Panhard
4 Link & Panhard, top adjustable trailing arms.
Shortened BW Diff.
New 28 spline axles.
New 3.73:1 gear set.
New 4 pinion LSD assembly.
|
|
simon clemens
Wed April 27, 2005 7:00am
|
LHS Axle, 'QA1' Coilover
Shortened BW Diff.
New 28 spline axles.
New 3.73:1 gear set.
New 4 pinion LSD assembly.
3 Position suspension height bracket on lower coilover eyelet.
12 Position dampen rate on 'QA1' shock. Plus adjustable spring tension.
|
|
