flipper35
Mon October 2, 2006 12:58pm
|
How short can a driveshaft be?
|
|
stefanog
Wed September 26, 2007 3:31am
|
08_03_0
nice to be noticed! Charity day for SES
|
|
MaSnaka
Sat May 17, 2008 3:25pm
|
New SS quick jack bumpers
Custom quick jacks for CR, polished stainless. Notice bolt spacing is wider on thr CR.
|
|
Duffinatur
Sun June 22, 2008 11:44pm
|
split_panel
I noticed this split panel on my trunk lid when I was wet sanding, damnit.
|
|
hi-tech cobra
Sat July 26, 2008 6:43am
Rating: 10
|
Hi-Tech engine bay
here is the engine bay before the sbf engine mounts were cut off. Notice also, the crossmember is set up for a top loader. This had to be cut off and the cross member notched to fit the Tremec.
|
|
Clois Harlan
Mon March 9, 2009 6:32pm
|
Installing the Bonnet
Notice the clean seams and smooth finish of the body
|
|
Clois Harlan
Mon March 9, 2009 6:32pm
|
HCS Body side shot
Notice the outer skin of the door is still taped in place for final fitments and then the adhesive will be applied to make it one piece.
|
|
Garage10
Sun April 19, 2009 10:37pm
|
rad
Notice the 5/8 hose barb on the upper right. That was being fed from surge tank. I will plug it and now go to outlet to water pump instead.
|
|
Tom Kirkham
Sun December 6, 2009 4:20pm
Rating: 10
|
68 Mustang Rally Car
notice Toyota truck rims
|
|
Tom Kirkham
Sun December 6, 2009 4:20pm
Rating: 10
|
68 Mustang Rally Car
notice additional shocks
|
|
FUNFER2
Sat February 6, 2010 5:36am
Rating: 10
|
Polished 304 stainless steel pipes. "Gilmore Kit".
Collector into muffler. Notice how the collector slides between the muffler & muffler housing, for a nice tight & clean fit. Requires only a small tig weld.
|
|
FUNFER2
Sat February 6, 2010 5:41am
Rating: 10
|
Polished 304 stainless steel side pipes."Gilmore Kit"
Turn out. Notice how it slides between the muffler & muffler housing, for a nice tight & clean fit. Requires only a small tig weld. Use filler rod if you wish to smooth the weld.
|
|
Mach 1 Fan
Tue March 18, 2014 9:41am
Rating: 10
|
notice license plate
1984 Aurora Mark II Cobra
|
|
Earl J
Mon April 14, 2014 2:03pm
Rating: 10
|
Bell-Crank close-up
Notice the Block I painted black. I stamped in a pointer (V painted in white) points to a scribed Red line on the #2 runner (just below the ARP carb stud). That is an indicator for me to view is my linkage is out of alignment. I hasn't moved once from the day i installed and adjusted it.
|
|
rodneym
Tue July 1, 2014 12:24pm
Rating: 10
|
disconnected Paxtons
I disconnected the Paxtons for a different flavor. Glad I did - I found a vacuum leak at one carb - never noticed it with positive pressure. Idles better, too. Now I have a track day option.
I considered giving the Paxtons a break for the Summer but she didn't run any cooler. Lesson learned.
|
|
