Karel289
Thu June 29, 2006 11:11am
|
3D Mirror finaly the right shape
|
|
fastraxsg
Fri January 12, 2007 6:35am
|
IMG_7377b
Compared to quality replica, distance above tires to top of fender is too high. Door is wrong shape and the fenders should come down in front of the windshield. Local Marvia replica, 1989
|
|
greg schroeder
Mon February 5, 2007 2:37pm
|
3rd gear data
3rd gear G-tech data vs. changes Superformance 2040 with Roush 427R-095
The power values represented are G-tech HP. This should not be confused with any other method of testing HP. It's only a number of reference.
Just as wheel HP on a chassis dyno is lower than flywheel HP because of additional drive line loss, the G-tech HP is lower than chassis dyno due to additional resistance such as aero drag and road resistance, even amount of air in tires would have a factor. As speed increases aero drag as well as other rolling resistance increase. For example as an estimate @ 50 mph there is an equivalent of approximately -12 HP, @ 100 mph -90 HP, @ 130 mph right about -200 HP for the shape of the Cobra.
|
|
CJ428CJ
Wed February 7, 2007 5:35pm
Rating: 10
|
Driveline
My new horseshoe shaped safety loop
|
|
1985 CCX
Tue May 8, 2007 6:57pm
Rating: 10
|
|
letsboogie351
Tue November 13, 2007 12:00am
Rating: 10
|
dashboard
Next the dash is off to have a timber centre piece shaped and polished. Dash will be covered in dark grey/charcoal leather prio to fitting timber centre
|
|
fastraxsg
Tue May 27, 2008 6:53am
|
One more crate to go
After many hours, still one crate to knock down. Kit weathered the journey half way around the world in good shape. Well packed by crew at the factory. Shipping cost almost as much as the kit.
|
|
392cobra
Sat May 31, 2008 11:19am
Rating: 10
|
Biker Babe Staying in Shape
|
|
Rick Yeager
Thu October 23, 2008 12:24am
Rating: 10
|
8_Door
Fitting doors and trying to shape them to fit the surrounding body areas
|
|
Z-linkCobra
Mon November 2, 2009 11:08am
Rating: 1
|
Driver inner door
I poured and shaped the foam. Once I finish the passanger side and smooth the dash....then fiberglass work starts.
|
|
Z-linkCobra
Mon November 2, 2009 11:08am
|
Dash and center console.
Once all the foam work is done and shaped...then all of it will get glassed in to the body. Making the dash, console and doors all one peice.
|
|
FUNFER2
Sat February 6, 2010 5:18am
Rating: 10
|
Hanger
This hanger has a weld tab that is shaped to fit the muffler housing and with the supplied bolts, is adjustable.
|
|
BMK
Sat February 20, 2010 8:10pm
Rating: 10
|
The Eichler home takes shape
Front of house after renovation. We purchased a run down Eichler stylehome. $100,000's later!!
|
|
52chevyred
Fri April 29, 2011 10:35am
|
Cobra visit at Jodeco Auto Body
Here is my Cobra in primer at Jodeco Auto Body. Bruce said the body was in great shape and didn't take a lot of work. They are about to seal the primer.
|
|
Wazza
Thu January 28, 2016 7:31pm
|
small seal strip shaped and silicone sealed
|
|
