 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| 1 |
2 |
3 |
4 |
5 |
6 |
7 |
| 8 |
9 |
10 |
11 |
12 |
13 |
14 |
| 15 |
16 |
17 |
18 |
19 |
20 |
21 |
| 22 |
23 |
24 |
25 |
26 |
27 |
28 |
|
|
CC Advertisers
|
|
|
17 result(s) to your search. (lifters)
|
· Next Page
|
|
Naja
Sat August 17, 2002 11:44am
|
Naked 533 cid EFI
A look at Naja's powerplant with most of the 'accessories' off of it. Atop is a 1200 cfm Accel throttle body, then a Torker II manifold (a significant restriction for this engine), to the new Edelbrock 6066 aluminum heads, 65 lb. Siemens injectors (supplied by an Aeroequip pump). Custom grind roller CompCam with .662 i/e lift, solid lifters, roller rockers under the custom valve cover by Innovation West (only ones like them in the world). A medium stoker with .080 overbore gives 533 cid. Wiseco pistons have 18cc dish to give 9.8:1 compression ratio. I was surprised when the redline was set at 7k, but the 2 people doing the engine work said it would have no trouble handling it.
It dyno'd at 491 hp (5200 rpm) and 548 ft-lbs (4700 rpm) - remember the Torker II being a huge restriction. It was built with reliability (first) in mind, then for torque. The lowest rpm that they data logged during the dyno was 2600, and it was already doing 525 ft-lbs.
This powers a C6 tranny leading to a 9 inch, live rear end with a 2.73 running gear. Haven't run it on the road much, but have gotten over 15 mpg on two, short trips. Spark control completely MSD including 7AL-2, Pro Power HVC coil, billet distributor with Pro cap. All of this is managed by a SpeedPro ECU. It idles at about 950 rpm.
|
|
djseed
Thu March 6, 2003 4:52pm
Rating: 10
|
Crane Roller Lifters and Rockers
Crane hydraulic roller lifters and Gold Race roller rockers.
|
|
ronzara
Sun August 10, 2003 4:28pm
Rating: 1
|
351W Almost completed
1972 351W, Polished GT-40X Aluminum Heads, REV Stainless Valves (underct stems, Turbo polished), Ford Motorsport 1.6 Roller Rockers, Keith Black KB-151 Pistons, Eagle Rods, Comp Cams Duel Energy Cam, Comp Cams Springs - Lifters - Push Rods - Timing Chain, Weiand Polished Stealth Intake & Water Pump, Polished Motorcraft Alternator. >>> the tough part is over,... I hope!
|
|
REDSC400
Thu November 6, 2003 5:17pm
Rating: 10
|
ERA 375 428FE Engine
Early photo (2003 December) of ERA375's engine, 1966 428FE from 1966 Thunderbird, fully blueprinted and balanced, 423HP at the rear wheels @ 5400 RPM, 450 Ft/Lbs torque at 3900 RPM. Holley 850 CFM Double Pumper Carb, Sidewinder Intake Manifold, Original Pent Roof Chrome Valve Covers with 427 Badges, Competition Cams 33-230-4 Cam, Dove Rocker support End Stands, 2.09" Intake and 1.75" Exhause, Milodon Circle Track 8 Qt oil pan, Forged A1 Pistons with SS-50 Rings, Forged Crank and Tie Rods, Auto Racing Products Head Studs, Crand Dual Stage Hydro Lifters, K&N Xstream Air Filter, MSD 6AL Igniton, Mallory Electronic Distributor with Magnecor KV85 Ignition Wires and Looms, High Pressure Oil Pump, Mallory Comp. Coil
|
|
aeroleague
Sat December 13, 2003 10:45pm
|
Engine
327 stroker Windsor.
351 block - .030 over
303Z roller cam
FM roller lifters
Aluminum Victor JR intake
Ford 400 offset turned crank - 4.387 stroke.
Eagle H beam connecting rods
J@E forged aluminum pistons- 10.5 compression.
Aluminum flywheel
MSD distributor
Edlebrock Victor Jr. heads
Comp Cams hardened push rods.
Comp CCams Magnum steel roller rockers
Comp Cams double roller timing chain.
750 cfm Speed Demon by Barry Grant.
|
|
Bruce Edwards
Thu May 6, 2004 3:53pm
Rating: 10
|
Bill's 351W front 2
Another picture of Bill's 351W (TampaFla) for his 289 ERA.
Somethings you do not see but that I will post when I get more time.
Forged Keith Black pistons .30, Double row timing set, .10/.10 crank, Hand fit Sealed Power 1/16 moly rings, trimetal Clevite 77 bearings, HP/HV Melling pump with a HD drive, Edelbrock Performer RPM cam, Roller tip rockers, Brass freeze plugs, Windage tray, Oil pan baffle welded into bottom of pan, Oil temp bung brazed to side of pan, High Rev anti pump up lifters, ARP Studs for mains,ARP rod bolts, modified oil pick up, treaded front oil galley plugs, matched block oil passage to oil pump and FelPro gaskets
|
|
luke-44
Sat July 24, 2004 11:52am
|
|
weirhouse
Wed October 6, 2004 8:11pm
|
ERA #414's 427 side oiler
1965 C5AE block, C7AE-9245-E PI intake, Holley 750, NASCAR crank & Le mans rods, Shelby aluminum heads, Isky cam & solid lifters, TRW pistons, 9.5:1 compression
|
|
LwCwb
Fri November 4, 2005 1:33pm
|
Caterpillar 3406BC Parts
Caterpillar Turbocharger, Oil Pan, Pushrods, Lifters, Fasteners, Fuel Lines, Injection Pump, Water Pump, and Temprature Sending Unit
|
|
silverstreak
Thu March 30, 2006 11:33am
|
promo pic, crane hyd roller lifters
|
|
HSSS427
Wed April 19, 2006 10:05am
|
ERA #414 427 side oiler after Keith Craft rebuild
427 side-oiler - C5AE-H
Shelby American aluminum heads, stage II port and polish
Forged crank C5AE-6300
Lemans Rods
Aluminum Police Interceptor intake - C6AE-9425-E
Mighty Demon 750 carb
Diamond Pistons
MSD 6AL electronic ignition and billett distributor w MSD 8.5mm wires
Comp Cams hydraulic roller camshaft: 242 duration, .645 lift, 248 duration, .635 lift
Crane lifters, Smith Bros push rods
|
|
HSSS427
Fri June 2, 2006 8:00pm
Rating: 10
|
|
Anthony
Sun May 20, 2007 5:51pm
Rating: 10
|
427 SO Hi-Riser heads
Here is a partially assembled 427 SO, '68 block with lifter galleries. 4.250 Bore ( 0.017" over), stock stroke. Dove aluminum Hi-Riser heads. Solid Roller cam, Roller-master Timing chain, Crower oil-fed roller lifters. Eagle rods.
|
|
onefastmustang
Sun October 4, 2009 5:41pm
|
|
FWB
Sun June 20, 2010 12:34pm
Rating: 10
|
roller lifters-oil galley
|
|
|
All times are GMT -7. The time now is 01:48 PM.
Links monetized by VigLink |
