speed220mph
Fri February 9, 2007 7:55am
Rating: 10
|
Smiths oil-pressure gauge with BSP adapter to AN-4 line
Finally found a BSP adapter to joint AN-4 swivel fitting to BSP threads on Smiths oil-pressure gauge.
|
|
speed220mph
Fri February 9, 2007 12:17pm
Rating: 10
|
Crack in Tunnel Port Head
Crack between intake-valve seat and sparkplug hole was repaired by pinning, replacing plug threads with Heli-Coil and installing new valve seat.
|
|
TWOOD
Fri March 14, 2008 4:29pm
|
DOOR LATCH RELEASE LINKAGE
View at top end of lionkage with the 1/4" dia. shaft passing through the bronze bushing (epoxied to fiberglass). Lever is attached to end of shaft. Hole in shaft is threaded and has nylock jam nuts on each side.
|
|
CSX3018
Mon August 11, 2008 4:15pm
|
Throttle linckage threaded rod & renforced tubing ,bellcrank SS
302 Ford Dart aluminimun block/heads 410 hp.
|
|
mickmate
Mon November 10, 2008 7:50pm
Rating: 10
|
289 Motor Mounts
289 motor mounts ready for install on frame see thread for original rubbers and brackets to go with them.
|
|
kitcarbp
Mon March 2, 2009 1:11pm
Rating: 10
|
oil temp sensor installed @ drain plug
Ford 460 crate engine with a modified drain plug with a 17mm hex head to accept a 1/8 NPT-27 threaded oil temp sensor.
|
|
DocDirk
Sat April 25, 2009 1:13pm
|
T at T-stat housing
I had to put a T in because I have no temp sender threaded site in the intake manifold. Probably going to be better to just go ahead and drill one.
|
|
kitcarbp
Mon September 21, 2009 8:22am
Rating: 10
|
VDO oil temp sender for oil pan drian plug- 14mm x 1.5
This oil temp sensor threads into 460 crate engine oil pan in place of the standard drain plug.
|
|
Dan Case
Sat January 16, 2010 3:03am
Rating: 10
|
6.5 Early Six Spoke Front (front side)
Bolt On Balance Weight Wheels, the bosses on the spokes are for bolt on wheel weights, a threaded rod went in from the rear, round lead weights when over the studs.
|
|
Z-linkCobra
Thu February 18, 2010 8:25am
|
Trunk hinge support
When I got this kit the trunk lid and hood were not attached to their frames. So before joining the two together I figured I would give the hinges something solid to bolt to...and also add some strength. The holes are 5/8 and I am making some press fit threaded collars to put in the holes for 3/8 bolts.
|
|
Z-linkCobra
Thu February 18, 2010 8:25am
|
hood support close up.
Here you see the steel threaded collars pressed into the 5/8's holes. I didnt want to thread the aluminum for fear of the threads possibly pulling through.
|
|
FWB
Sun June 20, 2010 12:34pm
|
edelbrock head thread inserts
|
|
Bitten Bob
Tue July 10, 2012 6:04am
Rating: 10
|
fuel leak
fuel leaking from fuel bow screw, due to stripped thread
|
|
rodneym
Fri July 15, 2016 11:11am
Rating: 10
|
In Loving Memory thread killer
In Loving Memory thread killer
|
|
Moriarty
Thu March 28, 2019 6:19pm
Rating: 10
|
|
