Wbulk
Fri July 16, 2010 1:32pm
Rating: 10
|
Rear Bumper Modification
Completed modication with the welded on bracket on the end of the tubes cut off and bolts going through to the frame bracket.
|
|
Wbulk
Wed September 1, 2010 1:41pm
|
B and B Door Hinge Modification
By drilling out the hinge for tapered bolts this allows for the door panel to set flush with door. Extra piece of 1/8" steel added in the front for strength.
|
|
kitcarbp
Thu October 14, 2010 7:36am
Rating: 10
|
stat o seal for fuel cell filler plate bolts
stat o seal for fuel cell filler plate, lifetime seal , no need to fuss with leaks ever again, expensive but permanenet and reuseable.
|
|
Jerry Clayton
Fri April 29, 2011 1:58pm
Rating: 10
|
IMG_0128_640x427_
Lakewood housing showing block plate with all the bolt holes for required bolts
|
|
Wazza
Sat August 6, 2011 9:29pm
|
4 Bolt Mains with the old 2 bolt cap sitting on top.
The old 2 bolt caps look a bit frail compared to the new 4 bolts.
|
|
AdamF
Sat August 13, 2011 9:36pm
|
GForce Cobra with the 'lid' off.
Here's the Cobra after installation in my shed and the body off. Wasn't too hard as the bolts were all fairly obvious.
|
|
LightNFast
Mon February 18, 2013 9:33am
Rating: 10
|
FIA_Suitcase_Study1
It’s documented that (2) AC factory cars were prepared with FIA suitcase "dimples" (See Photos). The second modification was to enlarge the trunk base to allow the suitcase to fit upright (vertical) and further down into the trunk as shown. If you look closely at the photo you can see the suitcase also fit horizontal and was held in place with a “bungee cord”. You can also see the bolts protruding out the bottom of the suitcase which originally held the suitcase upright. I think this also explains why some of the FIA cars had dimples while others didn’t.
As for the actual size of the suitcase – FIA Historic Racing Championships - Appendix J. Both 1964 and 1965.
State:
“270 - Luggage trunk
A covered space being an integral part of the coachwork but outside of the space occupied by the front seats, large enough to receive a trunk of
65 cm X 40 cm X 20 cm. minimum, besides the spare wheel, tools or the folded hood, shall be provided, excluding the spare wheel, tools or removed canopy.”
|
|
Mongoose930
Sun October 27, 2013 10:13am
Rating: 10
|
|
cobrajeff
Wed January 1, 2014 8:49am
|
oil cooler scoop
the aluminum sheet I trimmed the scoop out with is held in place with silicones at the front edge and the cooler bolts on the back edge
|
|
RGF
Sat July 26, 2014 11:45pm
|
Sterring column - four bolts
|
|
CompClassics
Wed January 27, 2016 3:50pm
Rating: 10
|
1964 and newer Weber 48IDA brass banjos, bolts and gaskets
Complete installation kit for brass banjos, brass bolt and gaskets when installing 48IDA Webers.
|
|
Morris
Thu July 20, 2017 1:37pm
|
|
Dan Case
Thu August 17, 2017 3:35pm
Rating: 10
|
Rocker Arm Cover Cap Screws
|
|
Dan Case
Mon September 4, 2017 4:54pm
Rating: 10
|
two types of GT350 header bolts
|
|
Moriarty
Wed April 17, 2019 9:36pm
Rating: 10
|
|
