cobrajeff
Sat October 7, 2006 4:24pm
Rating: 10
|
BOSS 351 with Webers in Pantera
Years before my Cobra replica became a reality, I had a genuine BOSS 351 engine (swapped out of my Dad's '71 BOSS 351 Mustang) with Webers on it in my '72 Pantera. When I sold the Pantera, I kept the BOSS engine and Webers, 'cause I knew that was what I wanted in my Cobra.
|
|
blueovalfanatic
Tue January 30, 2007 9:36pm
|
painted toploader
Yea, i'm obviously not going "original" with all the colors, but I wanted it blue. LOL
|
|
Anthony
Sat June 2, 2007 7:56am
|
chassis dyno Roush 427R
Here is a chassis dyno of a Roush 427R crate engine, as installed in a Superformance. They have installed many of these 427R engines in cobra's, and this is the best output any of the 427R engines had made. They are rated by Roush at 550 HP and 535 torque at the flywheel. The engine was not run above 5800 rpm's where you would expect to see max HP, but the max torque is a good value.
I wanted to use this engine as a benchmark to compare my 427 SO engine to. Both cars running the same sidepipes.
|
|
isaakgt
Sun October 14, 2007 9:20pm
Rating: 10
|
Busted!
What can I say, they wanted to look at the car.
|
|
Don Nolen
Tue January 15, 2008 9:32am
|
Cobra pix
I wanted one my whole life. A dream come true!
|
|
Pete Munroe
Wed July 22, 2009 9:58pm
Rating: 10
|
ERA 289 FIA shoulder harness mount
Roll bar mount for raising the shoulder harness. Moved one of the belt anchors to the outside of the roll bar. For the inside anchor I welded a bracket on the bar. Point was to be symmetrical to where I mounted the seat. Did not mount the seat as suggested in the "offset" position. Wanted it directly back from the pedals. Did lose some leg room by not doing the normal "offset".
|
|
*13*
Sun November 29, 2009 3:49pm
Rating: 10
|
Weber Filters (Home Made)
Just a first try. SS mesh & Neoprene caps from McMaster Carr. Just wanted to see if it would work. Now that I know they do, I can clean them up a bit. Blurry picture is hiding the dirty engine compartment.
|
|
52chevyred
Fri January 1, 2010 7:50am
|
Street Beasts Passenger Sidepipes
I bought the sidepipes "bare" from Street Beasts to save about $1,200 they wanted to coat them. I can get them done for about $500
|
|
Wazza
Mon January 25, 2010 6:01pm
Rating: 10
|
Our Unit
Wanted to change from living in a house in the suburbs....love the new outlook!
|
|
Wazza
Mon January 25, 2010 6:01pm
|
New Cobra build
The Thunderbird IRS means that the 3 inch system can't be tucked away as much as I wanted...might leave it on show like this.
|
|
Z-linkCobra
Fri September 3, 2010 3:04pm
|
Tail light mounting surface.
E.M. intended to use the dual round lights for the rear. I wanted to use the original ones but the area E.M. made for the light mount kind of looked wierd after I mounted it...so I fixed it for them...lol.
|
|
GForce
Tue March 26, 2013 10:33am
|
Bill Dyer wanted
Bill Dyer wanted
|
|
Hail427
Sat April 26, 2014 1:53am
Rating: 10
|
my Pace build #21
I wanted a yellow/bright colour how many times have you heard I didn't see you?
|
|
rodneym
Mon March 5, 2018 10:36pm
Rating: 10
|
Paxton SN93 cutaway
I always wanted to know how these things worked, so I cut up a junked one at my machine shop (at work). It still spins. If I cut deeper (including the races) to show the friction balls then I'll loose that ability, so it sits for now.
|
|
Dan Case
Thu April 18, 2019 10:42am
Rating: 10
|
|
