Secret Squirrel
Wed October 20, 2004 7:00am
Rating: 10
|
Rocker Arms Close Up
Close up of Edelbrock Performer RPM Aluminium Head with Roller Rocker Arms & RPM Air Gap Intake Manifold. 10/16/2004
|
|
cobrajeff
Sun November 21, 2004 12:04pm
Rating: 10
|
351C Weber Intakes
My "old" Weber manifold on left - "new" intake for B351 High Port Aluminum heads. The SVO manifoold popped up on e-bay at exactly the right time.
|
|
cobrajeff
Sun November 21, 2004 12:08pm
Rating: 10
|
351C Weber intakes
High-Port manifold on right. Note vacuum holes on inboard side, as opposed to th eold intake, where they were outboard.
Two bosses on intake for "hard" linkage, as opposed to th e"cable" linkage of the Pantera system.
|
|
Michael C Henry
Mon December 13, 2004 10:06pm
Rating: 10
|
new_lr
my fresh carbs ceramic coated intake manifold.my custom vent tubes
|
|
Terry Brown
Tue February 7, 2006 6:14am
Rating: 10
|
Weber Intake Vaccuum Lines
Underside of Weber Manifold with Vac lines (Traindriver's setup)
|
|
cobrajeff
Fri November 10, 2006 12:46pm
Rating: 10
|
Weber intakes for 351C
The lower manifold is a standard Weber intake for a 351 Cleveland. The upper one is port a 351C with "High-Port" heads. Note the difference in material above and below the port on the two manifolds.
|
|
greg schroeder
Mon February 19, 2007 5:30pm
|
dynojet 475.3 wheel HP
Roush 427R-095 single plane intake manifold
Pro-Systems 1000 cfm carb
oval 2.25 in. high air cleaner
2" primary headers
Buckshot Racefab side pipes
|
|
RJCCOBRA
Sat February 9, 2008 8:30am
|
Stroked 428CJ for Shell Valley kit
Stroked 428CJ for Shell Valley kit. 462 cubic inches, ported iron CJ heads, Erson roller rockers, Edlebrock Victor manifold, MSD distributor, BG 850 CFM carburetor, Isky cam 254@.050 intake; .580 lift/ 260@.050 exhaust; .588 lift. 570HP@5800/548TQ@4800
|
|
RJCCOBRA
Sat February 9, 2008 8:30am
|
Stroked 428CJ for Shell Valley kit
Stroked 428CJ for Shell Valley kit. 462 cubic inches, ported iron CJ heads, Erson roller rockers, Edlebrock Victor manifold, MSD distributor, BG 850 CFM carburetor, Isky cam 254@.050 intake; .580 lift/260@.050 exhaust; .588 lift. 570HP@5800/548TQ@4800
|
|
RJCCOBRA
Sat February 9, 2008 8:30am
|
Stroked 428CJ for Shell Valley kit
Stroked 428CJ for Shell Valley kit. 462 cubic inches, ported iron CJ heads, Erson roller rockers, Edlebrock Victor manifold, MSD distributor, BG 850 CFM carburetor, Isky cam 254@.050 intake; .580 lift/260@.050 exhaust; .588 lift. 570HP@5800/548TQ@4800
|
|
Snakebit
Fri June 27, 2008 7:01pm
Rating: 10
|
IMG_0155
Custom made Weber linkage polished stainless levers an polished intake manifold
|
|
fkemmerer
Thu July 31, 2008 6:02am
Rating: 10
|
ERA 753 - IAC Details
This picture shows the inside of the intake ports on my TWM stack injection setup. The brass fitting connect to the IAC motor plumbing under the intake manifold.
|
|
DocDirk
Sat April 25, 2009 1:13pm
|
T at T-stat housing
I had to put a T in because I have no temp sender threaded site in the intake manifold. Probably going to be better to just go ahead and drill one.
|
|
ekrupa2
Thu November 25, 2010 8:48am
|
Ceramic Coating Intake Manifold
Ceramic Coating Intake Manifold
|
|
ekrupa2
Thu November 25, 2010 8:48am
Rating: 10
|
Ceramic Coating Intake Manifold
Ceramic Coating Intake Manifold
|
|
