Brett J. Bolte
Fri January 17, 2003 11:53pm
Rating: 10
|
Read the glove box.... (click on blank photo to see)
Get in. Sit down. Shut up. Hold on.
|
|
427 S/O
Tue February 4, 2003 5:15am
|
swing_out_fuse_panel
swing out fuse panel, next to passengers foot box. carpeted
panel cover.
|
|
Sal Gerace
Fri February 28, 2003 10:49am
|
R-Model Fuse panel
R-Model fuse box. Car at Ac car show feb.,2003
|
|
cobrajeff
Tue December 2, 2003 5:24am
Rating: 10
|
Collapsible Spare Tire
Here is my "standard" load - Collapsible Spare seated between Halon and Battery box (air inlator bottle in green "wine cooler" bag).
Two folding chairs, California Duster, and emergency tool kit on lower level. Small scissors jack, knock-off hammer, safety wire & pliers, couple screwdrivers and spark plug socket w/rachet.
Soft top is only loaded when it looks like it will be needed. Miscellaneous "waxer" supplies in small black box to right of tool box.
|
|
Michael C Henry
Tue December 14, 2004 9:59am
Rating: 10
|
old_dash_right
Old EM painted dash .Steel rusting through and no glove box.functunal grab handle
|
|
Michael C Henry
Sat January 15, 2005 4:30pm
Rating: 10
|
Balast_and_shorting_plug
Balast resister with the shorting plug bypassing the Mallory HyFire box. When bypassing ,power that went to ignition box and now gos to the coil ,has to come through the resister.
|
|
flipper35
Thu May 5, 2005 1:55pm
Rating: 9
|
Cold_air_intake
Building a cold air box.
|
|
RobV
Mon June 13, 2005 7:37pm
|
Manual clutch shroud
I opted for the manual clutch set up. This is the fiberglass shroud. The B&B has a built in quadrant in the pedal box.
|
|
Zderf
Tue April 25, 2006 1:55pm
|
ShelbyBox
The worlds fastest tool box.
|
|
ebiggs1
Sun February 11, 2007 8:26am
|
Putting the body where it belongs.
Trouble here. i had to relocate the MSD box.
|
|
RJCCOBRA
Mon December 15, 2008 2:47pm
|
Shell Valley build
Brake lines installed between master cylinders and proportioning valve. A cover was fabricated and installed over the brake/clutch box.
|
|
kitcarbp
Tue June 23, 2009 7:01am
Rating: 10
|
alternator fuse with power distribution
I upgraded my electrical system to handle my twin SPAL fans (18A x 2 = 36 AMPS) by installing a modern Alt fuse power box. I used 4 gauge cable from alt to fuse and fuse to battery. It now serves my twin fans and main harness from this point and will give me an underhood power point.
|
|
Wbulk
Tue June 15, 2010 7:50pm
Rating: 10
|
Mechanical Carb Linkage
Mechanciall carb linkage in the foot box.
|
|
blip
Wed November 3, 2010 5:04am
Rating: 10
|
Me waiting for some track laps at Silverstone
This is a Shelby approved car Factory built by Ram Automotive, using the superb Reynard spaceframe chassis, running a 1970 Ford 351 Cleveland with quenched Aussie heads, through a 5 speed Getrag manual box.
Jag rear axle.
|
|
powrby4d
Wed September 23, 2020 3:33pm
Rating: 10
|
SVC cobra clutch bellcrank type arm
This arm is on my Shell Valley Cobra that comes out of the back of the firewall inboard of the brake master cylinder which is bolted to the firewall. So the left to right position of the pedals is actually reversed on the firewall due to some strange linkage inside the pedal box. Try8ng to find out if this is part of the reason why my clutch is essentially undrivable, and whether this is a standard Shell Valley thing or some kind of complex setup somebody did to avoid the headers.
|
|
