 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
1 |
2 |
| 3 |
4 |
5 |
6 |
7 |
8 |
9 |
| 10 |
11 |
12 |
13 |
14 |
15 |
16 |
| 17 |
18 |
19 |
20 |
21 |
22 |
23 |
| 24 |
25 |
26 |
27 |
28 |
29 |
30 |
| 31 |
|
|
|
|
|
|
|
|
CC Advertisers
|
|
|
5 result(s) to your search. (inch,)
|
·
|
|
Naja
Sat August 17, 2002 11:18am
|
Chassis Rear
Rear view of the West Coast chassis. 9 inch, live axle with 2.73 gearing. 11 inch ventilated brakes. It's heavy, but extremely rigid and makes for a FINE road car.
|
|
Naja
Sat August 17, 2002 11:44am
|
Naked 533 cid EFI
A look at Naja's powerplant with most of the 'accessories' off of it. Atop is a 1200 cfm Accel throttle body, then a Torker II manifold (a significant restriction for this engine), to the new Edelbrock 6066 aluminum heads, 65 lb. Siemens injectors (supplied by an Aeroequip pump). Custom grind roller CompCam with .662 i/e lift, solid lifters, roller rockers under the custom valve cover by Innovation West (only ones like them in the world). A medium stoker with .080 overbore gives 533 cid. Wiseco pistons have 18cc dish to give 9.8:1 compression ratio. I was surprised when the redline was set at 7k, but the 2 people doing the engine work said it would have no trouble handling it.
It dyno'd at 491 hp (5200 rpm) and 548 ft-lbs (4700 rpm) - remember the Torker II being a huge restriction. It was built with reliability (first) in mind, then for torque. The lowest rpm that they data logged during the dyno was 2600, and it was already doing 525 ft-lbs.
This powers a C6 tranny leading to a 9 inch, live rear end with a 2.73 running gear. Haven't run it on the road much, but have gotten over 15 mpg on two, short trips. Spark control completely MSD including 7AL-2, Pro Power HVC coil, billet distributor with Pro cap. All of this is managed by a SpeedPro ECU. It idles at about 950 rpm.
|
|
W2zero
Sat May 14, 2005 8:14pm
|
FRPP rear disc, Dutchman axles
Narrowed nine inch, Detroit locker, 4.11 gears, Dutchman 31sp axles, FRPP rear disc brakes.
|
|
Jac Mac
Tue April 12, 2011 10:35pm
Rating: 10
|
9 inch Ford Independent rear center section.
9 inch Ford Diff assy, mounts on 4 pads on rear of housing plus 'ring' bracket that attach's to pinion retainer. This particular unit has now completed seven hard seasons of classic racing in a TVR Tuscan. We are now upgrading the axle shafts to 35 spline to make it totally bulletproof...if such a state ever exists!:)
|
|
52chevyred
Sun May 18, 2014 4:34pm
Rating: 10
|
Front of Hinge cut at 3/4"
Here is where the "original hinge" is cut, 3/4" inch, after the hinge pin. This is on the "front side", before the pipe is installed.
|
|
|
All times are GMT -7. The time now is 10:29 PM.
Links monetized by VigLink |
