Club Cobra Keith Craft Motorsports  

Go Back   Club Cobra > Search Forums
Reload this Page Search Results
Portal Register FAQ Community For Sale Gallery Calendar Today's Posts

Nevada Classics
MMG Superformance
Main Menu
Portal
Forums

Module Jump:
Nevada Classics
Nevada Classics
Advertise at CC
Banner Ad Rates
MMG Superformance
Keith Craft Racing
MMG Superformance
January 2026
S M T W T F S
        1 2 3
4 5 6 7 8 9 10
11 12 13 14 15 16 17
18 19 20 21 22 23 24
25 26 27 28 29 30 31
Page 1 of 4 1 234
Showing results 1 to 25 of 100
Search took 0.03 seconds. Search: Posts Made By: Richard Hudgins
Forum: All Racing Talk 11-17-2018, 01:25 AM
Replies: 27
Views: 2,153
Posted By Richard Hudgins
I was not clear in the last post. I am not...

I was not clear in the last post.

I am not speaking of any spacers but rather the width of the wheel to fit the tyres that xlr8tr was speaking about and its offset relative to the stock wheel.
...
Forum: All Racing Talk 11-16-2018, 04:26 PM
Replies: 27
Views: 2,153
Posted By Richard Hudgins
Good catch. If done the way I stated it would...

Good catch. If done the way I stated it would indeed alter the scrub radii and wheel rotation would be difficult due to the wheel/upright interference drag induced by the clamping force of the lug...
Forum: All Racing Talk 11-14-2018, 08:57 PM
Replies: 27
Views: 2,153
Posted By Richard Hudgins
The Comp chassis would accept the section widths...

The Comp chassis would accept the section widths that you quote as there is room for the increased wheel width while maintaining the same outside dimensions and therefore the motion ratios would...
Forum: All Racing Talk 11-11-2018, 02:18 PM
Replies: 27
Views: 2,153
Posted By Richard Hudgins
The only good data that I still have of skid pad...

The only good data that I still have of skid pad testing was back in 2004.

JBL Comp chassis/302 on 200 ft skidpad at Willow Springs with Michelin Pilots

Best lap = 14.52 seconds = 1.16g. ...
Forum: ALL COBRA TALK 09-11-2017, 06:01 PM
Replies: 90
Views: 7,006
Posted By Richard Hudgins
Body tooling only. And only for the Goins...

Body tooling only. And only for the Goins modified bodywork as used on the touring chassis.

And yes, the JBL comp chassis car is NLA.

Dave is virtually retired and only building races parts....
Forum: ALL COBRA TALK 05-30-2016, 12:31 AM
Replies: 8
Views: 652
Posted By Richard Hudgins
I didn't get all of the Fords (30's to Late 40's)...

I didn't get all of the Fords (30's to Late 40's) with small block Chevy's.
Forum: ALL COBRA TALK 05-29-2016, 07:49 PM
Replies: 8
Views: 652
Posted By Richard Hudgins
Some nice looking Cobras there in particular the...

Some nice looking Cobras there in particular the 289 cars. But in my estimation the show stopper was this little devil.

http://www.jblmotor.com/images/004sch.jpg...
Forum: Coupe Talk 03-26-2016, 01:27 PM
Replies: 162
Views: 31,169
Posted By Richard Hudgins
Try this: T56 Magnum Ford TKO Speed Sensor...

Try this: T56 Magnum Ford TKO Speed Sensor Pigtail Harness | eBay (http://www.ebay.com/itm/T56-Magnum-Ford-TKO-Speed-Sensor-Pigtail-Harness-/281805591731)
Forum: Coupe Talk 02-04-2016, 07:09 PM
Replies: 162
Views: 31,169
Posted By Richard Hudgins
Clois, You might wish to look at the Howe...

Clois,

You might wish to look at the Howe Surge tanks. (They are reference builder of the radiators for the comp chassis.) See. https://www.howeracing.com/p-7460-surge-tanks.aspx
Forum: Coupe Talk 01-21-2016, 08:55 PM
Replies: 162
Views: 31,169
Posted By Richard Hudgins
Just to get a few things/facts correct here if...

Just to get a few things/facts correct here if you do not mind.

1. Larry Goins/Goins Motorsports has never made any brake parts for the JBL. They were all made in CA at the JBL/SKS facilities...
Forum: Cobra Build Logs 10-08-2015, 08:06 PM
Replies: 141
Views: 34,528
Posted By Richard Hudgins
Matt, Looks and sounds good. I noticed that...

Matt,

Looks and sounds good. I noticed that you were working the brake bias a bit. I would recommend that you set it (after everything is hot) by adjusting toward the rear until they...
Forum: ALL COBRA TALK 09-10-2015, 12:25 PM
Replies: 14
Views: 1,636
Posted By Richard Hudgins
I tried a couple of airfield type auto-crosses...

I tried a couple of airfield type auto-crosses many years ago and just could not get a grip on the course layouts. The cones just blended together. (Or collected themselves under my car)

For...
Forum: Small Block Talk 05-01-2015, 09:23 PM
Replies: 11
Views: 3,578
Posted By Richard Hudgins
ianm12, Methinks that there might be just a...

ianm12,

Methinks that there might be just a bit more to it than whipping up some bits and mounting them inboard.

Then again, maybe not. :D

And from what I have heard, the Touring chassis...
Forum: Arntz/Butler Forum 02-17-2015, 08:24 PM
Replies: 25
Views: 3,293
Posted By Richard Hudgins
Joeyv, The pricing to replace your fuel...

Joeyv,

The pricing to replace your fuel cell, feed and return system seems high by a factor of about 4.

First thing. What make is your fuel cell? Is it a bladder type? Is it a standard size...
Forum: Small Block Talk 12-21-2014, 05:24 PM
Replies: 13
Views: 1,245
Posted By Richard Hudgins
Brett, I do not know what pedal assembly you...

Brett,

I do not know what pedal assembly you have. Either the Tilton or the Wilwood units fit the pedal box.

Each one uses a different adjuster cable.

If it was my car I would fab up an...
Forum: Small Block Talk 12-21-2014, 12:39 PM
Replies: 13
Views: 1,245
Posted By Richard Hudgins
Brett, I designed the chassis to use bespoke...

Brett,

I designed the chassis to use bespoke steering column parts. I used pultruded S-glass/carbon 1 inch shafts with bonded spline inserts and Borgeson joints.

Goodwinds...
Forum: ALL COBRA TALK 12-05-2014, 04:32 PM
Replies: 30
Views: 5,261
Posted By Richard Hudgins
Tim7139, I hope the below information is...

Tim7139,

I hope the below information is what you are asking for.

Bill. S,

We did do some third party testing and below are the results. (I must say that I was disappointed in the...
Forum: ALL COBRA TALK 12-03-2014, 08:29 PM
Replies: 17
Views: 10,054
Posted By Richard Hudgins
Some vehicle aero flow visualizations with some nerdy scoop stuff

Folks,

This video may help in everyone's understanding the flows around the Cobra. I know the vehicles are quite different from the Cobra but the video is still applicable.

Flow...
Forum: Small Block Talk 11-23-2014, 02:57 PM
Replies: 20
Views: 3,454
Posted By Richard Hudgins
Brett, You are making a mountain out of a...

Brett,

You are making a mountain out of a molehill on your motor.

I am sure that the experts will say that I am absolutely full of it and things would be best if my advice was quietly but...
Forum: ALL COBRA TALK 11-20-2014, 09:04 PM
Replies: 45
Views: 6,138
Posted By Richard Hudgins
I had a Traco 5 liter 90 degree sbc in a Lola...

I had a Traco 5 liter 90 degree sbc in a Lola T330 (A long time ago) and I bought a HRE flat crank motor as a replacement as the Traco was getting long in the tooth and the HRE motor was cheaper.
...
Forum: ALL COBRA TALK 10-24-2014, 06:42 PM
Replies: 92
Views: 10,172
Posted By Richard Hudgins
mikeinatlanta, It seems to me that you might...

mikeinatlanta,

It seems to me that you might wish to try the wonders of Photoshop as you are obviously only interested in visuals.

That way you can avoid being insulted by folk's "rude...
Forum: Tech Tips 06-11-2014, 05:22 PM
Replies: 20
Views: 3,921
Posted By Richard Hudgins
ajr, The only long lasting cure is to not...

ajr,

The only long lasting cure is to not get them hot.

Here is some basic information about heat tint on Stainless from the British Stainless Steel Association.

Heat tint (temper) colours...
Forum: All Racing Talk 04-21-2014, 09:21 PM
Replies: 9
Views: 1,472
Posted By Richard Hudgins
Dailey should put a pressure tap on the pump at...

Dailey should put a pressure tap on the pump at each stage. Scavenge stages as well.

We always put them in the pumps after we got them from whatever vendor.

We used each tap on the dyno and...
Forum: ALL COBRA TALK 03-31-2014, 03:08 PM
Replies: 10
Views: 940
Posted By Richard Hudgins
DMXF, I am going to assume that the...

DMXF,

I am going to assume that the chemistry that you are looking at using is LI-FePo4 as this is the normal for large scale cells and readily available.

The problem is cell balancing as...
Forum: ALL COBRA TALK 02-19-2014, 08:40 PM
Replies: 16
Views: 3,404
Posted By Richard Hudgins
Brilliant

Brilliant
Showing results 1 to 25 of 100
Page 1 of 4 1 234

 

All times are GMT -7. The time now is 01:02 AM.

Contact Us - Club Cobra Home - Archive - Top

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink