Domed Filters for your TWM Injection

Blittleton · #1 (**permalink**) 01-02-2010, 05:05 PM

Here are the new Domed Filters that we are selling. Very nice product, get in non polished polished and anodizing. These are complete from the stacks and up. These are not cheap. This will give anyone who needs more clearance with there hoods. Please give me a call for more information at 859-630-9099. These filters are made for TWM,Webbers, Imagine Injection units.

Excaliber · #2 (**permalink**) 01-02-2010, 05:26 PM

Eight tiny air filters for your sleigh...

LMH · #3 (**permalink**) 01-02-2010, 06:11 PM

I don't even have Webers and I'd love a set of those!!
Maybe a table center peice...hmmm.
Larry

csx4910 · #4 (**permalink**) 01-02-2010, 06:26 PM

I can attest to the quality and fit and finish of these. I ended up with teh first prototype of these as no one else makes a proper filter that would fit under my csx hood with the 511 motor. Pricey yes, but absolutley beautiful. In the end I couldn't put a price on not sucking desert dust down those throttle bodies. I got mine in polished.
ron

StreetSnake · #5 (**permalink**) 01-02-2010, 06:27 PM

Very very nice. How much restriction do they have, or in other words how much hp lost. If I already didn't spend a small fortune on the roush ones you could sign me up. What is the going price? Beautiful

SoTxButler · #6 (**permalink**) 01-02-2010, 06:27 PM

Is that foam under the screen or some kind of fabric and is material sandwiched between two screens?

RodKnock · #7 (**permalink**) 01-02-2010, 06:33 PM

Those are very nice. I assume that they could also be anodized in satin black, semi-gloss black and gloss black?

Mando · #8 (**permalink**) 01-02-2010, 08:53 PM

Absolutely Beautiful!

Regards.

tkb289 · #9 (**permalink**) 01-02-2010, 10:21 PM

The entire setup looks great ... bet it looks even better under the hood of a Cobra !

Blittleton · #10 (**permalink**) 01-03-2010, 10:22 AM

These have the same material as a regular filter. I know that the filter element has been tested on what hp loss there was, but these had the best results. I'm not sure on the numbers but I will inquire about it. Anodizing could be in any style you wish. Color of the element can be changed as well.

Bill

Kramer · #11 (**permalink**) 01-03-2010, 02:21 PM

Who can I contact about these filters?

Kramer

Blittleton · #12 (**permalink**) 01-03-2010, 03:54 PM

contact me tomorrow at 859-630-9099 ask for Bill.

Blittleton · #13 (**permalink**) 01-05-2010, 04:58 PM

Single place set of 8 billet hi flow filters with velocity stacks, screw top rings and black filters under stainless steel mesh. The filter material is a multiple layered cotton for high filtration.

Bill

Stentor · #14 (**permalink**) 01-05-2010, 08:13 PM

These look like the filters made by C. Cook Enterprises in Kentucky. They were mentioned in a thread about two years ago.

I talked to them a month or so ago, and am considering getting a set for my IDAs. They are a bit on the pricey side.

SF_SN888KE · #15 (**permalink**) 01-09-2010, 09:04 AM

Beautiful! So, it sounds like you replace your old stacks with a new set of stacks (pricy in itself) and the new stacks have a screw on top for the filters?

What effect will these new stacks have on tuning with the manometer? (unscrew the filter and good to go?)

Bill - What's the cost?

I'm sitting down ...

Blittleton · #16 (**permalink**) 01-09-2010, 09:35 AM

You are correct about the stack are swapped out. small block start out at 1250.00. You may want the low dome or high dome. That is why I would like you to contact me. There are a lot of variables in your decision. My number is 859-630-9099

bill

SF_SN888KE · #17 (**permalink**) 01-09-2010, 04:53 PM

Is there any effect on tuning with a manometer? e.g. unscrew filter and manometer fits as usual?

Blittleton · #18 (**permalink**) 01-10-2010, 09:57 AM

It will be the same.

Bill