Club Cobra Gas - N Exhaust  

Go Back   Club Cobra > Cobra Talk Areas > ALL COBRA TALK

Nevada Classics
Keith Craft Racing
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
Keith Craft Racing
MMG Superformance
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            

Kirkham Motorsports

Like Tree4Likes
  • 2 Post By 1Gooddeal
  • 1 Post By hi-tech cobra
  • 1 Post By hi-tech cobra

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 05-06-2020, 09:06 AM
Registered User
Visit my Photo Gallery

 
Join Date: May 2020
Location: Lauderdale by the Sea, FL
Cobra Make, Engine: Arizona 1997 Hi Tech
Posts: 1
Not Ranked     
Default Help with Hi-Tech Motorsport 1997 from AZ

Trying to identify front and rear brakes, I'm working on a cobra that was built in 97 from high-tech in Arizona I'm familiar with some of the history of the builder, I'm looking for information for what applicat of wilwood front and rear brakes, it has an independent 9-inch rear and I do not know what the axle housings are for the rear and the spindles for the front to order the brakes I do not have calipers or rotors and they are knock-off hubs on the spindles, anybody have any information identifying the rear and front suspension so I can order the brakes wilwood I've been on the phone with them and we're trying to sort it out but it's a little bit of a guessing game because we didn't build the suspension and we don't know what application of the parts that are needed.
Any help greatly appreciated thank you.
Attached Images
  
1985 CCX and hi-tech cobra like this.
Reply With Quote
  #2 (permalink)  
Old 05-06-2020, 04:13 PM
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Rosemount, Mn
Cobra Make, Engine: SPF 1233-396C.I. Windsor
Posts: 121
Not Ranked     
Default

Wilwood Superlite calipers have a 3 1/2" bolt spacing for the caliper mounts. Dynalites are either 5" or 5 1/2" - sorry, I can't remember.. Looks like a typical 8 bolt rotor (8 bolts on a 7" bolt circle). Rotor diameter will be 11.75" or 12.19" diameter. You may have to mock something up to determine rotor width and diameter. PM me if you get stuck, good luck.
__________________
Mike Beamish / Northern Racing Products Superformance service & installation.
Reply With Quote
  #3 (permalink)  
Old 05-07-2020, 09:27 AM
hi-tech cobra's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Mar 2006
Location: Jacksonville, FL
Cobra Make, Engine: Hi-Tech
Posts: 475
Not Ranked     
Default

Always good to meet a fellow Hi-Tech brother. Let me know if I can help.
1Gooddeal likes this.
Reply With Quote
  #4 (permalink)  
Old 05-07-2020, 09:29 AM
hi-tech cobra's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Mar 2006
Location: Jacksonville, FL
Cobra Make, Engine: Hi-Tech
Posts: 475
Not Ranked     
Default

http://www.clubcobra.com/photopost/d.../DSC_0005b.jpg
1Gooddeal likes this.
Reply With Quote
  #5 (permalink)  
Old 05-07-2020, 11:00 AM
Sawdust's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2010
Location: North of Toronto, Ont
Cobra Make, Engine: Superformance #1950, Roush 402R, TKO600
Posts: 552
Not Ranked     
Default

Could you take a picture of the pads and provide exact measurements to Wilwood in hopes they can match the pads?
Reply With Quote
  #6 (permalink)  
Old 05-07-2020, 04:32 PM
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Rosemount, Mn
Cobra Make, Engine: SPF 1233-396C.I. Windsor
Posts: 121
Not Ranked     
Default

Picture looks like Superlites- rotor width appears to be 1.250. Better question is anyone have pics of the rears? Not uncommon to run a .810 wide rotor in the rear. Rear does a small percentage of total braking so we use calipers with smaller pistons. Fronts should be staggered bore -1.875 & 1.750 piston. Rears calipers will be sold to specific rotor width and usually have 1.375 or 1.250" pistons. These are 4 piston calipers.
__________________
Mike Beamish / Northern Racing Products Superformance service & installation.
Reply With Quote
  #7 (permalink)  
Old 05-20-2020, 12:28 PM
hi-tech cobra's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Mar 2006
Location: Jacksonville, FL
Cobra Make, Engine: Hi-Tech
Posts: 475
Not Ranked     
Default

I tried sending pics. Having problems PM'ing you. PM me your email and I'll send.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 04:18 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink