Club Cobra Keith Craft Motorsports  

Go Back   Club Cobra > Cobra Talk Areas > ALL COBRA TALK

Keith Craft Racing
Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Keith Craft Racing
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
Keith Craft Racing
Keith Craft Racing
February 2026
S M T W T F S
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 09-02-2007, 04:25 PM
SuperHart's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2001
Location: Cinnaminson, NJ
Cobra Make, Engine: Cobra Fibercraft Bodies 427 S/C, 351W disguised as a 427.
Posts: 391
Send a message via AIM to SuperHart
Not Ranked     
Default

The way my system is plumbed you are correct, the oil to pressurize the system is drawn from the oil pan. However, the oil is forced through the oil filter before being delivered to the engine so metal is not a problem. I agree that unfiltered oil should not be pumped into the engine and had the same concern until I studied the schematic. If you think about it, the oil route using the Preluber is the same as when drawn from the pan via the oil pump; pan -->oil pump -->oil cooler --> oil filter --> engine bearings. I run a Canton T-sump road race pan. There is a fitting on the side of the sump that I used for the preluber pickup. Therefore oil is sucked from approximately one inch up from the bottom of the pan, actually higher in the sump than the oil pump pickup is located (1/2" from the bottom). There is indeed a check valve in the Preluber unit that prevents reverse oil flow back to the pan. Unlike the Accusump, this powered system is great to use to pressurize the engine following an oil and filter change. Just turn the key to ON and allow the unit to build pressure. I have noted that following an oil and oil filter change on an engine with an oil cooler it does take several seconds to build oil pressure at the first start. Without this system the engine would have to be cranked and run without oil pressure for that several seconds until all the air is purged.

For those individuals concerned about loss of oil pressure during cornering, etc. this should never happen if the oil pickup screen was set up correctly to begin with and if there is a proper oil level on the dipstick. Since most of us run a mechanical oil presure gauge and might not be looking at it if and when the oil pressure suddenly drops to Zero, I offer the following suggestion: on the oil pressure gauge fitting on the side of the block install a 1/8 NPT T fitting to allow installation of both the mechanical capillary tube AND an electric sending unit. Plumb the sending unit to a red dash light and a buzzer. If the oil pressure takes a nose dive the light will illuminate and the buzzer will warn you immediately to kill the engine.
__________________
Political correctness is a doctrine, fostered by a delusional, illogical minority, and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end."

Last edited by SuperHart; 09-02-2007 at 04:47 PM..
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 06:32 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink