 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
|
|
|
|
|
1 |
| 2 |
3 |
4 |
5 |
6 |
7 |
8 |
| 9 |
10 |
11 |
12 |
13 |
14 |
15 |
| 16 |
17 |
18 |
19 |
20 |
21 |
22 |
| 23 |
24 |
25 |
26 |
27 |
28 |
29 |
| 30 |
|
|
|
|
|
|
|
|
CC Advertisers
|
|
03-14-2009, 02:56 PM
|
 |
Senior Club Cobra Member
|
|
|
Join Date: Feb 2005
Cobra Make, Engine: Contemporary, FE, Tremec TKO 600
Posts: 1,956
|
|
Not Ranked
Where to buy rubber grommets for thicker Fiberglass firewall?
Unless I am missing them, I don't see thick panel rubber grommets in McMaster Carr for using on my firewall and other panels in my car. I'm about to start the electrical part of the project. It seems that a grommet to fit a 1/4" thick panel is the thickest panel thickness I can see in McMaster-Carr, and even then it is only in very limited sizes. As best I can tell my firewall is about 1/4" thick, and then I have an aluminum panel over that. Also, I have wires to pass through bulkheads and such, all of them seem to be 1/4" thick. Any ideas where to source this stuff, guys? Thanks.
Doug
|
03-14-2009, 06:37 PM
|
|
CC Member
|
|
|
Join Date: Dec 2004
Location: Kansas City,
KS
Cobra Make, Engine: jbl
Posts: 2,291
|
|
Not Ranked
i picked up some grommets at an aircraft surplus supply house.
|
03-14-2009, 07:11 PM
|
 |
CC Member
|
|
|
Join Date: Feb 2004
Cobra Make, Engine: FFR 390 toploader IRS
Posts: 258
|
|
Not Ranked
__________________
FFR MarkIII,FE,toploader,IRS,3.27,Vintage pin's SOLD!
68 F100 Custom Cab 418 cube FE/auto
99 SuperDuty Tuner/chipped/4" Banks TOTALED!!
02 Super Duty 7.3L
Last edited by convincor; 03-14-2009 at 07:22 PM..
|
03-14-2009, 08:46 PM
|
 |
CC Member
|
|
|
Join Date: Dec 2001
Location: San Diego,
CA
Cobra Make, Engine:
Posts: 2,977
|
|
Not Ranked
Depending on how big you want them you can use valve cover breather grommets. They are grooved for about a 1/4 inch thick panel and work pretty well.
__________________
Remember, It's never too early to start beefing up your obituary.
|
03-14-2009, 11:40 PM
|
 |
CC Member
|
|
|
Join Date: Feb 2006
Location: Gore. New Zealand.,
SI
Cobra Make, Engine: DIY Coupe, F/T ,MkIV.
Posts: 808
|
|
Not Ranked
Boat builders should be able to point you in the right direction.
__________________
Jac Mac
|
03-15-2009, 02:11 AM
|
 |
Senior Club Cobra Member
|
|
|
Join Date: Dec 2001
Location: Shasta Lake,
CA
Cobra Make, Engine:
Posts: 26,555
|
|
Not Ranked
Also you might try one of the big truck repair places.I got a bunch of stuff like that from the big Peterbilt repair place a few miles from my house when I was building my Cobra. They had a huge selection of almost every kind of grommets, lights, and anything else odd that I needed.
Ron
|
03-15-2009, 03:58 AM
|
|
CC Member
|
|
|
Join Date: Mar 2006
Cobra Make, Engine:
Posts: 21
|
|
Not Ranked
http://www.mcmaster.com
This site is amazing. And they deliver fast. They have hudred of grommets and you can shop from the comfort of your home.
Brian
|
03-15-2009, 06:13 AM
|
|
CC Member
|
|
|
Join Date: Mar 2006
Cobra Make, Engine:
Posts: 277
|
|
Not Ranked
PACER Wire and Cable. SkinTop 2 Liquid tight connectors. I use them all the time in my boat building.
|
03-16-2009, 10:39 AM
|
|
CC Member
|
|
|
Join Date: May 2007
Cobra Make, Engine: JCF supplied the body,frame,and some of the driveline-I completed it to be a very accurate 289 slabside
Posts: 144
|
|
Not Ranked
Grommets
The best source for grommets and other parts is Restoration Specialties & Supply,Inc. http://www.restorationspecialties.co...og%20ebook.pdf
They have grommets with groove widths up to 1/4". |
10-29-2009, 05:27 AM
|
|
Senior Club Cobra Member
|
|
|
Join Date: Nov 2006
Location: Charleston,
WV
Cobra Make, Engine: SPF 2592, Shelby alum. 527
Posts: 325
|
|
Not Ranked
Resurrecting an old thread. I found this site and thought someone might find it useful.
They have quite a selection; groove widths up to 5/8".
http://cableorganizer.com/grommet/
Rodger |
02-23-2012, 03:59 AM
|
|
CC Member
|
|
|
Join Date: Feb 2012
Cobra Make, Engine:
Posts: 1
|
|
Not Ranked
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 08:19 AM.
Links monetized by VigLink
|
Linear Mode
